Effects of PWB design factors on PTH reliability
-
摘要: 基于镀通孔(PTH, Plated Through-Hole)应力分布模型,定量地研究了PTH线路板厚度与PTH直径之比(高径比)、PTH半径与镀层厚度之比、线路板有效作用半径与PTH半径之比等几何设计参数以及线路板玻璃化温度对PTH镀层应变及寿命的影响.通过引入等效温度载荷,给出了不同玻璃化温度下的应力分布模型.研究表明,在屈服温度载荷附近时,PTH应变和寿命对几何尺寸非常敏感.在固定线路板有效作用半径与PTH半径之比后,PTH高径比影响较为明显.对于一定厚度的线路板,PTH半径越小,镀层最大应变越大,寿命越低.在玻璃化温度以上,应变急剧增加.研究还表明应变集中系数并非固定不变,而是在弹性和塑性范围内有所变化.Abstract: Based on the barrel stress distribution model, the effect of printed wiring board(PWB) design factors such as plated through-hole(PTH) aspect ratio, the ratio of plating thickness over PTH radius, the ratio of board influence radius over PTH radius and glass transition temperature on PTH barrel stress and lifetime were studied quantitatively. Equivalent temperature load was introduced to found the barrel stress distribution model under different glass transition temperature. Results show that PTH life is sensitive to design factors when PWB operating at vicinities of the yielding temperature load. The PTH aspect ratio shows more significant impact when fixing the ratio of board influence radius over PTH radius. For the fixed PWB thickness, decrease PTH diameter results in the increase of PTH barrel stress and the decrease of PTH lifetime. PTH barrel strain sharply increases at the glass transition temperature. Results also show that the constant strain concentration coefficient is different in elastic and plastic stage.
-
Key words:
- plated through hole /
- design parameter /
- glass transition temperature /
- lifetime /
- reliability
-
[1] Michael F, Donald B. Predicting plated though hole life and in the field from thermal stress data IPC Printed Circuits Expo, APEX and the Designers Summit. Los Angeles:The Institute for Interconnecting and Packaging Electronic Circuits, 2006:203-205 [2] Xie Jingsong, Kang Rui, Zhang Yuan, et al. A PTH reliability model considering barrel stress distributions and multiple PTHs in a PWB The 44th Annual IEEE International Reliability Physics Symposium. San Jose:IEEE Electron Device Society and IEEE Reliability Society, 2006:256-265 [3] Mirman B A. Mathematical model of a plated-through hole under a load induced by thermal mismatch[J]. IEEE Transactions on Components, Hybrids and Manufacturing Technology, 1988,11(4):506-511 [4] Iannuzzelli R. Predicting plated-through-hole reliability in high temperature manufacturing processes Proceedings of the 41st Electronic Components and Technology Conference. Atlanta:The IEEE Components, Packaging and Manufacturing Technology Society, 1991:410-421 [5] Xie Jingsong, Huo Yujie, Zhang Yuan, et al. Effect of PWB design factors and glass transition temperature on PTH reliability The 39th International Symposium on Microelectronics. Washington DC:International Microelectronics and Packaging Society and The Microelectronics Foundation, 2006:534-537 [6] Kobayashi T, Hayashida S. A study on reliability modeling for through hole cracking failure in thermal enhanced PBGA laminate Electronic Components and Technology Conference. Las Vegas:The IEEE Components, Packaging and Manufacturing Technology Society, 2000:1658-1660 [7] 孙博,张叔农,谢劲松. PCB镀通孔疲劳寿命对设计参数的灵敏度分析[J].电子元件与材料, 2006,25(9):60-66 Sun Bo, Zhang Shunong, Xie Jingsong. Sensitivity analysis for the dependence of PTH fatigue life on PCB design parameters [J]. Electronics Components and Materials, 2006, 25(9):60-66(in Chinese) [8] Round R. Reliability evaluation of small diameter plated through holes in printed wiring boards . IPC-TR-579, 1988 -
点击查看大图
计量
- 文章访问数: 3733
- HTML全文浏览量: 249
- PDF下载量: 1048
- 被引次数: 0
下载:
