2219-T87高强铝合金HPVP-GTAW焊缝成形参数

李玉龙; 从保强; 杨明轩; 齐铂金

doi:10.13700/j.bh.1001-5965.2013.0380

2219-T87高强铝合金HPVP-GTAW焊缝成形参数

doi: 10.13700/j.bh.1001-5965.2013.0380

北京航空航天大学机械工程及自动化学院, 北京 100191

基金项目:

国家自然科学基金资助项目（51005011）；中央高校基本科研业务费专项资金资助项目（YWF-12-LGJC-001）

详细信息

作者简介:
李玉龙（1987- ），男，山东德州人，硕士生，lyl6310206@126.com.

中图分类号: TG457.14
计量
- 文章访问数: 1444
- HTML全文浏览量: 75
- PDF下载量: 452
- 被引次数: 0
出版历程
- 收稿日期: 2013-06-28
- 网络出版日期: 2014-05-20

Weld appearance of 2219- T 87 high strength aluminum alloy produced by HPVP-GTAW process

School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 采用复合超高频脉冲方波变极性钨极氩弧焊技术（HPVP-GTAW，Hybrid ultrahigh frequency Pulse Variable Polarity Gas Tungsten Arc Welding）完成了2219-T87高强铝合金平板堆焊试验，研究了HPVP-GTAW工艺脉冲电流参数对焊缝成形参数的影响规律.结果表明，与常规变极性钨极氩弧焊（VP-GTAW）工艺相比，HPVP-GTAW工艺有利于增加焊缝熔深，提高焊缝深宽比；调节脉冲电流参数，将对焊缝成形行为产生显著影响.在正极性期间平均电流恒定的条件下，随着脉冲电流频率的增加，焊缝熔深、深宽比整体提高，60 kHz条件下深宽比增加了60%；适当增大脉冲峰值电流与基值电流的比值，焊缝深宽比有所增大；与占空比50%和80%条件相比，20%条件下焊缝深宽比最高，且随着峰值电流与基值电流比值的提高，其焊缝深宽比增幅最为明显.
- 高强铝合金 /
- 变极性钨极氩弧焊 /
- 焊缝成形 /
- 脉冲电流 /
- 深宽比
Abstract: Based on hybrid ultrahigh frequency pulse variable polarity gas tungsten arc welding (HPVP-GTAW) surfacing process for 2219-T87 high strength aluminum alloy, the effect of pulse current parameters on weld appearance was analyzed. Experimental results show that the weld penetration and weld depth to width was improved significantly by HPVP-GTAW process, compared with the conventional VP-GTAW process. The weld appearance was changed obviously when the pulse current parameters were adjusted. With constant average current at positive polarity duration, the weld penetration and weld depth to width was overall improved with the increase of the pulse frequency, and weld depth to width increased by 60% when the pulse frequency reached up to 60 kHz. Weld depth to width was improved with the increasing of the ratio of the pulse peak current and base current. Weld depth to width was the highest with 20% duty cycle and improved most significantly with the increase pulse current ratio compared with the duty cycle of 50% and 80%.
- high strength aluminum alloy /
- variable polarity gas tungsten arc welding(VP-GTAW) /
- weld appearance /
- pulse current /
- weld depth to width

HTML全文

参考文献(10)

[1]	Cong B Q, Qi B J,Li Wei,et al.A novel ultrafast-convert hybrid pulse square-wave VP-GTAW process for aluminum alloys[J].China Welding,2010,19(2):32-36
[2]	从保强,齐铂金, 周兴国,等.高强铝合金复合脉冲VPTIG焊缝组织和性能[J].北京航空航天大学学报,2010,36(1): 1-5 Cong Baoqiang,Qi Bojin,Zhou Xingguo,et al. Microstructure and mechanical properties of hybrid pulse VPTIG arc welding of high strength aluminum alloy[J].Journal of Beijing University of Aeronautics and Astronautics,2010,36(1):1-5(in Chinese)
[3]	Potluri N B, Ghosh P K,Gupta P C,et al.Studies on weld metal characteristics and their influence on tensile and fatigue properties of pulsed current GMA welded Al-Zn-Mg alloy[J].Welding Journal,1996,75(2):62-70
[4]	王乐笑,从保强, 齐铂金,等.超高频脉冲方波电流对5A06铝合金HPVP-GTAW焊缝的影响[J].焊接学报,2013, 34(3) :61-64,116 Wang Lexiao,Cong Baoqiang,Qi Bojin,et al.Effect of ultrahigh frequency pulse square-wave current on 5A06 aluminum alloy HPVP-GTAW joints[J].Transactions of the China Welding Institution,2013,34(3):61-64,116(in Chinese)
[5]	从保强,齐铂金, 周兴国,等.超高频脉冲方波电流参数对2219铝合金焊缝组织和力学性能的影响[J].金属学报,2009,45(9):1057-1062 Cong Baoqiang,Qi Bojin,Zhou Xingguo,et al.Influences of ultrasonic pulse square-wave current parameters on microstructures and mechanical properties of 2219 aluminum alloy weld joints[J].Acta Metallurgica Sinica,2009,45(9):1057-1062(in Chinese)
[6]	安藤弘平, 长谷川光雄.焊接电弧现象[M].北京:机械工业出版社,1985:249-250 Ando Kohei,Hasegawa Mitsuo.The phenomenon of welding arc[M].Beijing:China Machine Press,1985:249-250(in Chinese)
[7]	贾昌申,肖克民, 殷咸青.焊接电弧的等离子流力研究[J].西安交通大学学报,1994,28(1):23-28 Jia Changshen,Xiao Kemin,Yin Xianqing.The plasmas flow force of welding arc[J].Journal of Xi'an Jiaotong University,1994,28(1):23-28(in Chinese)
[8]	赵家瑞. 电流脉冲频率对TIG焊电弧影响机理的研究[J].电焊机,1993(2):16-18 Zhao Jiarui.Mechanism of pulse current frequeney effeet on TIG arc[J].Electric Welding Machine,1993(2):16-18(in Chinese)
[9]	Cook G E, Eassa E H.The effect of high-frequency pulsing of a welding arc[J].Transactions on Industry Applications,1985,1A-21(5):1294-1299
[10]	Praveen P, Yarlagadda P,Kang M J.Advancements in pulse gas metal arc welding[J].Journal of Materials Processing Technology,2005(164/165):1113-1119