Thermal characteristic of aerostatic direct-driven rotary stage
-
摘要: 以开发满足精密工程应用的静压气浮直驱转台为目标,研究静压气浮直驱转台结构的热稳定性.首先,分析了静压气浮直驱转台的发热-传热特性,建立了三维热特性有限元模型,计算了气浮直驱转台的温度场云图;用间接耦合的分析方法,将温度场作加载条件,进行转台热-结构耦合分析;然后,对比研究了两种直驱电机安置结构对转台热稳定性的影响,提出了静压气浮直驱转台的空气强制对流冷却方案;最后,完成了无框力矩电机后置式静压气浮直驱转台的温度场检测实验.实验结果表明,静压气浮直驱转台测试点的计算与实测温度的最大误差为1.93 ℃,稳态温度场分布计算精度较高;温度分布稳态时,气浮转台止推轴承气膜单侧间隙的变化量为0.55 μm,在空气轴承气膜设计允许的波动范围内,对轴承性能不产生明显的影响.电机后置式直驱静压气浮转台结构的热稳定性好,适合工业应用.Abstract: In order to develop a precision aerostatic direct-driven rotary stage for precision engineering application, the thermal structure stability and forced cooling method were investigated. First, the heat generation and heat transfer characteristics of this aerostatic direct-driven rotary stage were analyzed, and finite element model of thermal characteristics was set up. The temperature field distribution in the aerostatic direct-driven rotary table was obtained. Then, according to the indirect coupling analysis method, the thermal-structural coupling deformation of the rotary stage was calculated by taking the temperature field as loading conditions. Next, through comparing thermal deformation, the aerostatic direct-driven rotary stage structure thermal stability was discussed, and an air forced convection cooling method and the gas circuit design were provided. Finally, temperature field distribution test experiments were carried out. Experimental results indicate that temperature field distribution calculator precision is high, and maximum bias of the finite element calculation is 1.93 ℃, and the air film thickness change of the thrust air bearing is less than 0.55 μm which is within the permitted range and has no effect on air bearing performance. The rear-motor aerostatic direct-driven rotary stage has good thermal stability and is suitable for industrial application.
-
[1] Zhang C P, Li M, Luo X K.Thermal characteristics analysis of aerostatic direct drive rotary stage[J].Advanced Materials Research, 2013, 655-657:287-291 [2] Zhu J C, Chen H, Chen X D. Large eddy simulation of vortex shedding and pressure fluctuation in aerostatic bearings[J].Journal of Fluids and Structures, 2013, 40:42-51 [3] Chen X D, Chen H, Luo X, et al.Air vortices and nano-vibration of aerostatic bearings[J].Tribology Letters, 2011, 42(2):179-183 [4] Chen X D, He X M.The effect of the recess shape on performance analysis of the gas-lubricated bearing in optical lithography[J].Tribology International, 2006, 39(11):1336-1341 [5] 吴贺. 超高速空气静压电主轴热特性分析[D].广州:广东工业大学, 2012 Wu He.Analysis on the thermal characteristics of ultra high-speed aerostatic motorized spindle[D].Guangzhou:Guangdong University of Technology, 2012(in Chinese) [6] 王保民, 胡赤兵, 孙建仁, 等.高速电主轴热态特性的ANSYS仿真分析[J].兰州理工大学学报, 2009, 35(1):28-31 Wand Baomin, Hu Chibing, Sun Jianren, et al. Simulation analysis of thermal characteristics of high-speed motorized spindle by using ANSYS[J].Journal of Lanzhou University of Technology, 2009, 35(1):28-31(in Chinese) [7] Bossmanns B, Tu J F.A power flow model for high speed motor-ized spindles—heat generation characterization[J].Journal of Manufacturing Science and Engineering, 2001, 123(3):494-505 [8] 张从鹏, 罗学科, 谢峰. 一种静压气浮直驱转台:中国, 201010294885[P].2012-04-18 Zhang Congpeng, Luo Xueke, Xie Feng.A aerostatic direct drive rotary stage:China, 201010294885[P].2014-04-18(in Chinese) [9] 张明华, 袁松梅, 刘强.基于有限元分析方法的高速电主轴热态特性研究[J].制造技术与机床, 2008(4):29-32 Zhang Minghua, Yuan Songmei, Liu Qiang.Research on thermal characteristics for high speed motorized spindle based on finite element analysis[J].Manufacturing Technology & Machine Tool, 2008(4):29-32(in Chinese) [10] 陈兆年, 陈子辰. 机床热态特性学基础[M].北京:机械工业出版社, 1989 Chen Zhaonian, Chen Zichen.Machine tool thermal state characteristics[M].Beijing:Mechanical Industry Press, 1989(in Chinese) [11] 李美波. 高性能静压气浮运动系统热耦合分析及热误差控制[D].北京:北方工业大学, 2013 Li Meibo.Research on thermal characteristic and thermal error control of high-performance aerostatic motion system[D].Beijing:North China University of Technology, 2013(in Chinese) [12] 池长青. 气体动静压轴承的动力学及热力学[M].北京:北京航空航天大学出版社, 2008 Chi Changqing.Dynamics and thermodynamics for gas bearing[M].Beijing:Beihang University Press, 2008(in Chinese) [13] 陈学东, 何学明. 超精密气浮定位工作台技术——气浮系统动力学与控制[M].武汉:华中科技大学出版社, 2008 Chen Xuedong, He Xueming.Research on ultra precise positioning stage with gas-lubricated bearings—dynamics and control of the gas-lubricated system[M].Wuhan:Huazhong University of Science and Technology Press, 2008(in Chinese) [14] 戴锅生. 传热学[M].北京:高等教育出版社, 2002:21-53 Dai Guosheng.Heat transfer theory[M].Beijing:Higher Education Press, 2002:21-53(in Chinese) [15] 刘剑. 划片机空气静压主轴静态与热态特性的有限元分析与实验研究[D].上海:华东理工大学, 2011 Liu Jian.Static and thermal characteristics finite element analysis and experimental study of aerostatic spindle in dicing[D].Shanghai:East China University of Technology University, 2011(in Chinese)
点击查看大图
计量
- 文章访问数: 1185
- HTML全文浏览量: 129
- PDF下载量: 921
- 被引次数: 0