留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

变速器齿轮振动机理及修形减振降噪方法

岳会军 张尧 李洪彪 张敬 单红波

岳会军, 张尧, 李洪彪, 等 . 变速器齿轮振动机理及修形减振降噪方法[J]. 北京航空航天大学学报, 2017, 43(10): 2003-2010. doi: 10.13700/j.bh.1001-5965.2016.0814
引用本文: 岳会军, 张尧, 李洪彪, 等 . 变速器齿轮振动机理及修形减振降噪方法[J]. 北京航空航天大学学报, 2017, 43(10): 2003-2010. doi: 10.13700/j.bh.1001-5965.2016.0814
YUE Huijun, ZHANG Yao, LI Hongbiao, et al. Transmission gear vibration mechanism and modification method for vibration and noise reduction[J]. Journal of Beijing University of Aeronautics and Astronautics, 2017, 43(10): 2003-2010. doi: 10.13700/j.bh.1001-5965.2016.0814(in Chinese)
Citation: YUE Huijun, ZHANG Yao, LI Hongbiao, et al. Transmission gear vibration mechanism and modification method for vibration and noise reduction[J]. Journal of Beijing University of Aeronautics and Astronautics, 2017, 43(10): 2003-2010. doi: 10.13700/j.bh.1001-5965.2016.0814(in Chinese)

变速器齿轮振动机理及修形减振降噪方法

doi: 10.13700/j.bh.1001-5965.2016.0814
基金项目: 

国家科技支撑计划 2011BAG09B00

详细信息
    作者简介:

    岳会军, 男, 博士。主要研究方向:机械传动、传动系统的振动与噪声分析

    通讯作者:

    岳会军, E-mail: yuehuijun87@sina.com

  • 中图分类号: TH132.413;U463.212

Transmission gear vibration mechanism and modification method for vibration and noise reduction

Funds: 

National Key Technology Research and Development Program of China 2011BAG09B00

More Information
  • 摘要:

    以某款自动变速器为研究对象,对齿轮振动机理和斜齿轮修形减振降噪方法开展深入研究。采用SimulationX仿真和试验方法,确定对系统振动贡献量最大的齿轮对;采用有限元法进行内部激励详细分析,包含传递误差、接触斑点、啮合冲击和轮齿的热变形;在考虑齿轮温度场影响前提下,以传递误差波动小、消除啮合冲击和齿面接触状态良好为优选目标,经大量仿真结果对比,确定修形方案。修形后试验结果表明,齿轮修形方案可行,改善了齿轮传动状态,有效地减小了变速器的振动噪声。

     

  • 图 1  8AT结构图

    Figure 1.  8AT structure diagram

    图 2  8AT仿真模型

    Figure 2.  8AT simulation model

    图 3  3挡相对能量损失

    Figure 3.  Relative energy loss of Gear 3

    图 4  整车试验和台架试验

    Figure 4.  Vehicle test and bench test

    图 5  3挡振动信号频谱图和缓慢加速噪声

    Figure 5.  Vibration signal spectrogram and slow acceleration noise of Gear 3

    图 6  挡加载20 N·m阶次谱图和噪声切片图

    Figure 6.  Order spectrum and noise slice image of Gear 3 with 20 N·m load

    图 7  齿面和齿根网格划分细密图

    Figure 7.  Network partition of tooth surface and tooth root

    图 8  修形前传递误差曲线

    Figure 8.  Curve of transmission errors before modification

    图 9  修形前主动轮接触斑点图

    Figure 9.  Contact spot for driver before modification

    图 10  修形前齿根应力变化图

    Figure 10.  Variation diagram of tooth root stress before modification

    图 11  温度场分析有限元网格

    Figure 11.  Finite element meshes for temperature field analysis

    图 12  温度场分析结果

    Figure 12.  Results of temperature field analysis

    图 13  8AT模型

    Figure 13.  8AT model

    图 14  修形后传递误差曲线

    Figure 14.  Curve of transmission errors after modification

    图 15  修形后主动轮接触斑点图

    Figure 15.  Contact spot for driver after modification

    图 16  修形后齿根应力变化图

    Figure 16.  Variation diagram of tooth root stress after modification

    图 17  修形前后噪声水平对比

    Figure 17.  Comparison of noise level before and after modification

    图 18  齿轮10接触情况试验结果

    Figure 18.  Test results of contact status for Gear 10

    表  1  部件编号

    Table  1.   Serial number of components

    部件编号 部件
    1 太阳轮-行星轮啮合(行星排1)
    2 齿圈-行星轮啮合(行星排1)
    3 太阳轮-行星轮啮合(行星排2)
    4 齿圈-行星轮啮合(行星排2)
    5 太阳轮-行星轮啮合(行星排3)
    6 齿圈-行星轮啮合(行星排3)
    7 齿轮5-齿轮8啮合
    8 齿轮4-齿轮7啮合
    9 齿轮6-齿轮10啮合
    10 齿轮2-齿轮11啮合
    下载: 导出CSV

    表  2  齿轮参数

    Table  2.   Parameters of gears

    参数 齿轮6(主动轮) 齿轮10(从动轮)
    模数/mm 1.3 1.3
    齿数 61 132
    压力角/(°) 17.5 17.5
    螺旋角/(°) 18(左旋) 18(右旋)
    齿侧间隙 0.075 0.075
    变位系数 -0.077 0.150
    齿顶圆直径/mm 86.3 184.38
    齿根圆直径/mm 77.72 176.8
    齿宽/mm 15 14
    齿轮内径/mm 67.5 63
    中心距/mm 132 132
    扭矩/(N·mm) 178000 178000
    下载: 导出CSV

    表  3  齿轮温度场计算参数

    Table  3.   Parameters for calculating gear temperature field

    参数 数值
    黏度/(m2·s-1) 1.00×10-5
    热传导系数/(W·(m·K)-1) 0.1322
    比热/(J·(kg·K)-1) 2100
    密度/(kg·m-3) 845
    动力黏度/(MPa·s) 8.45
    导温系数 7.450×10-8
    Prandtl数 134.23
    弹性模量/Pa 2.06×1011
    综合弹性模量/Pa 2.25×1011
    齿面粗糙度/μm 0.8
    粗糙度因子 6.698
    热膨胀系数/℃-1 1.2×10-5
    下载: 导出CSV

    表  4  齿向修形方案

    Table  4.   Modification scheme of tooth trace

    倾斜量/μm 鼓形量/μm
    0 1 21
    0 0-0 0-1 0-21
    1 1-0 1-1 1-21
    7 7-0 7-1 7-21
    下载: 导出CSV

    表  5  齿廓修形方案

    Table  5.   Modification scheme of tooth profile

    滚转角/(°) 修形量/μm
    1 2 27
    11.3 11.3-1 11.3-2 11.3-27
    12.3 12.3-1 12.3-2 12.3-27
    13.3 13.3-1 13.3-2 13.3-27
    14.3 14.3-1 14.3-2 14.3-27
    15.3 15.3-1 15.3-2 15.3-27
    下载: 导出CSV
  • [1] KAHRAMAN A.Free torsional vibration characteristics of compound planetary gear sets[J]. Mechanism and Machine Theory, 2001, 36(8):953-971. doi: 10.1016/S0094-114X(01)00033-7
    [2] 方源, 章桐, 于蓬, 等.电动车动力总成内部激励的研究分析[J].振动、测试与诊断, 2014, 34(3):496-502. http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCS201403016.htm

    FANG Y, ZHANG T, YU P, et al.Research and analysis of the internal excitations of electric powertrain[J]. Journal of Vibration, Measurement & Diagnosis, 2014, 34(3):496-502(in Chinese). http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCS201403016.htm
    [3] 刘辉, 蔡仲昌, 项昌乐.发动机激励下行星传动非线性啮合力特性[J].振动、测试与诊断, 2014, 34(1):83-89. http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCS201401022.htm

    LIU H, CAI Z C, XIANG C L.Study on nonlinear meshing force dynamic behavior of planetary gears on engine excitation[J]. Journal of Vibration, Measurement & Diagnosis, 2014, 34(1):83-89(in Chinese). http://www.cnki.com.cn/Article/CJFDTOTAL-ZDCS201401022.htm
    [4] DUDLEY D W.Gear handbook[M]. New York:McGraw-Hill Co., 1962:6-22.
    [5] 周延泽, 吴继泽.直齿锥齿轮齿根应力的有限元分析[J].北京航空航天大学学报, 1996, 22(1):88-93. http://www.cnki.com.cn/Article/CJFDTOTAL-BJHK601.018.htm

    ZHOU Y Z, WU J Z.Finite element analysis of tooth root stress of straight bevel gear[J]. Journal of Beijng University of Aeronautics and Astronautics, 1996, 22(1):88-93(in Chinese). http://www.cnki.com.cn/Article/CJFDTOTAL-BJHK601.018.htm
    [6] PARK S J, YOO W S.Deformation overlap in the design of spur and helical gear pair[J]. Finite Elements in Analysis and Design, 2004, 40(11):1361-1378. doi: 10.1016/j.finel.2003.10.003
    [7] HARRIS S L.Dynamic loads on the teeth of spur gears[J]. Proceedings of Institution of Mechanical Engineers, 1958, 172(1):87-112. doi: 10.1243/PIME_PROC_1958_172_017_02
    [8] SMITH R E.Single-flank testing of gears[J]. Gear Technology, 2004, 21(3):18-21. http://www.geartechnology.com/issues/0504x/smith.pdf
    [9] KIRACOFE D R, PARKER R G.Structured vibration modes of general compound gear systems[J]. Journal of Vibration and Acoustics Transactions of the ASME, 2007, 129(1):1-16. doi: 10.1115/1.2345680
    [10] BLOK H.The dissipation of frictional heat[J]. Applied Scientific Research, 1955, 5(2-3):151-181. doi: 10.1007/BF03184615
    [11] BLOK H.The thermal-network method for predicting bulk temperature in gear transmission[M]. New York:Wiley, 1969:11-30.
    [12] VAN HEIJNINGEN G J J, BLOK H.Continuous as against intermittent fling-off cooling of gear teeth[J]. ASME Journal of Lubrication Technology, 1974, 96(4):529-538. doi: 10.1115/1.3452476
    [13] TERAUCHI Y, NAGAMURA K. 圆柱直齿轮轮齿的变形计算和齿廓修形[J]. 李德滋, 译. 齿轮, 1984, 8(3): 42-48.

    TERAUCHI Y, NAGAMURA K.On tooth deflection calculation and profile modification of spur gear tooth[J]. LI D Z, translated.Journal of Mechanical Transmission, 1984, 8(3):42-48(in Chinese).
    [14] SIGGN.Tooth profile modification of high speed duty gear[C]//Proceedings of International Conference on Gearing.New York:McGraw-Hill Co., 1958:313-316.
    [15] DUDLEYB W.Hand book of practical gear design[M]. New York:McGraw-Hill Co., 1984:193-235.
    [16] 高维金, 王亮, 刘永光.箱式动力结构的振动传递特性分析[J].北京航空航天大学学报, 2015, 41(3):509-516. http://bhxb.buaa.edu.cn/CN/abstract/abstract13195.shtml

    GAO W J, WANG L, LIU Y G.Analysis on vibration transmission characteristics of box-like power structure[J]. Journal of Beijng University of Aeronautics and Astronautics, 2015, 41(3):509-516(in Chinese). http://bhxb.buaa.edu.cn/CN/abstract/abstract13195.shtml
  • 加载中
图(18) / 表(5)
计量
  • 文章访问数:  837
  • HTML全文浏览量:  149
  • PDF下载量:  464
  • 被引次数: 0
出版历程
  • 收稿日期:  2016-10-19
  • 录用日期:  2016-11-11
  • 网络出版日期:  2017-10-20

目录

    /

    返回文章
    返回
    常见问答