无传感器的工业机器人负载识别方法

陈友东; 季旭东; 谷平平; 胡国栋

doi:10.13700/j.bh.1001-5965.2014.0669

无传感器的工业机器人负载识别方法

doi: 10.13700/j.bh.1001-5965.2014.0669

1.
北京航空航天大学机械工程及自动化学院, 北京 100191
2. 安徽埃夫特智能装备有限公司, 芜湖 241007

基金项目: 国家“863”计划(2014AA041601)

详细信息

通讯作者:
陈友东(1973—),男,安徽庐江人,副教授,chenyd@buaa.edu.cn,主要研究方向为工业机器人.

中图分类号: TP242
计量
- 文章访问数: 1027
- HTML全文浏览量: 88
- PDF下载量: 15908
- 被引次数: 0
出版历程
- 收稿日期: 2014-10-28
- 网络出版日期: 2015-09-20

Identifying method of load for sensorless industrial robot

1.
School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
2. Anhui Efort Intelligent Equipment Co., Ltd, Wuhu 241007, China

摘要

摘要: 工业机器人在使用过程中,由于末端负载的变化导致机械振动,因此需要识别机器人末端负载去调整相应的控制参数来保证其具有良好的运动表现.提出一种基于伺服电机输出力矩,不需要额外传感器的机器人负载识别方法.根据机器人静力学模型,计算出静止状态下末端空载和负载情况下的输出力矩差异,由此得到负载计算模型.对埃夫特的QH165机器人进行了试验,在工作空间内随机选择10个测量点,在末端空载和负载的情况下读取电机输出的力矩,计算得到末端负载.结果表明:识别的负载与已知负载相同,试验表明该方法的可行性.
- 工业机器人 /
- 负载识别 /
- 伺服电机 /
- 传感器 /
- 负载模型
Abstract: When the load of the industrial robot end-effector is changed in practical use, mechanical vibration occurs, in order to get high motion performance of the industrial robot, the end-effector load should be identified to modify the control parameter. A method of identifying load by servo motor output torque was proposed, which did not need an additional sensor. According to the static model of the robot, the load calculation model was achieved by the output torque difference between the end-effector with and without load. In the industrial workspace of the EFFORT QH165 robot, we randomly selected 10 measurement points to read the servo motor torque and calculated the load respectively. The results show that load identified by this method is the same with the given load. Through the experiments on the robot, the effectiveness of the proposed method is confirmed.
- industrial robot /
- load identification /
- servo motor /
- sensor /
- load model

HTML全文

参考文献(17)

[1]	Ko C M,Chung G J,Kin D H.Designing of heavy duty handling robot (HEDURI-I robot design)[C]//Proceedings of the 2009 IEEE International Conference on Mechatronics.Piscataway,NJ:IEEE Press,2009:1-6.
[2]	Feng Y L,Qu D K,Xu F,et al.Analysis and compensation for the dynamic error of the FPD glass substrates transfer robot[C]//IEEE International Conference on Robotics and Automation.Piscataway,NJ:IEEE Press,2011:1-3.
[3]	Lu D M,Zhang C Q,Fan Y Z,et al.The kinematic self-calibration method and simulation of one palletizing robot[C]//Proceedings of the 8th World Congress on Intelligent Control and Automation.Piscataway,NJ:IEEE Press,2010:6424-6427.
[4]	Guang X Q,Wang J D.Mechanical design and kinematic analysis of a new kind of palletizing robot[C]//Mechanic Automation and Control Engineering.Piscataway,NJ:IEEE Press,2011:199-202.
[5]	Tsumugiwa T,Watanabe Y,Yokogawa R.Robot motion control using mechanical load adjuster with motion measurement interface for human-robot cooperation[C]//Intelligent robots and systems.Piscataway,NJ:IEEE Press,2009:467-472.
[6]	Song Y F,Wang H G,Gao W B,et al.Dynamic deformation analysis of a spot welding robot under high speed and heavy load working condition[C]//IEEE International Conference on Robotics and Biomimetics.Piscataway,NJ:IEEE Press,2013:2043-2048.
[7]	Seki K,Nakamura H,Iwasaki M,et al.Suppression of resonant vibration due to angular transmission errors of reduction gearing in industrial robots[C]//IEEE International Conference on Mechatronics (ICM).Piscataway,NJ:IEEE Press,2013:835-840.
[8]	Huang L S,Qu D K,Xu F.Motion control strategy of industrial direct drive robot for vibration suppression[C]//Intelligent Control and Automation.Piscataway,NJ:IEEE Press,2010:2430-2433.
[9]	Hamon P,Gautier M,Garrec P,et al.Dynamic identification of robot with a load-dependent joint friction model[C]//Robotics Automation and Mechatronics.Piscataway,NJ:IEEE Press,2010:129-135.
[10]	Hamon P,Gautier M,Garrec P.Dynamic identification of robots with a dry friction model depending on load and velocity[C]//Intelligent Robots and Systems.Piscataway,NJ:IEEE Press,2010:6187-6193.
[11]	Paul R P.Robot manipulators:Mathematics,programming,and control[M].Cambridge:MIT Press,1981:157-195.
[12]	Coiffet P.Robot technology:Interaction with the environment[M].2nd ed.Englewood Cliffs:Prentice-Hall,1983:102-128.
[13]	Amitabha M.Adaptation in biological sensory-motor systems:A model for robotic control[C]//Intelligent Robots and Computer Vision.Bellingham,WA:SPIE,1984,521:243-247.
[14]	Amitabha M,Ballard D H.Self-calibration in robot manipulators[C]//Robotics and Automation.Piscataway,NJ:IEEE Press,1985:1050-1057.
[15]	Olsen H B,Bekey G A.Identification of parameters in models of robots with rotary joints[C]//Robotics and Automation.Piscataway,NJ:IEEE Press,1985:1045-1050.
[16]	Atkeson C G,An C H,Hollerbach J M.Estimation of inertial parameters of manipulator loads and links[J].International Journal of Robotics Research,1986,5(3):101-119.
[17]	Swevers J,Verdonck W,de Schutter J.Dynamic model identification for industrial robots[J].IEEE Control Systems Magazine,2007,27(5):58-71.