Material parameters in 3D finite element analysis of composite structure

[1] Taylor R M,Owens S D.Correlation of an analysis tool for 3-D reinforced bonded joints on the F-35 joint strike fighter .AIAA-2004-1562,2004 [2] Butler B.Composites affordability initiative .AIAA-2000-1379,2000 [3] Zhao Libin,Qin Tianliang,Huang Hai,et al.Model investigation on composite failure prediction of joint structures[J].Rare Mental Materials and Engineering,2009,38(S3):105-108 [4] 张志民.复合材料结构力学[M].北京:北京航空航天大学出版社,1993:30-32 Zhang Zhimin.Structural mechanics of composite materials [M].Beijing:Press of Beijing University of Aeronautics and Astronautics,1993:30-32(in Chinese) [5] 沈真,杨胜春.飞机结构用复合材料的力学性能要求[J].材料工程,2007(增刊1):248-252 Shen Zhen,Yang Shengchun.Property requirements of composite systems applicable to aircraft structures [J].Journal of Materials Engineering,2007(Supplement 1):248-252(in Chinese) [6] Christensen R M.Tensor transformation and failure criteria for analysis of fiber composite materials[J].Journal of Composite Materials,1988,22(9):874-897 [7] Feih S,Shercliff H R.Composite failure prediction of single-L joint structures under bending[J].Composites A:Applied Science and Manufacturing,2005,36(3):381-395 [8] Krueger R,O’Brien T K.A shell/3D modeling technique for the analysis of delaminated composite laminates[J].Composites:Part A,2001,32(1):25-44 [9] Jones R,Sawyer J P,Chiu W K.Studies in the matrix dominated failures of composite joints[J].Composite Structures,1999,44(1):1-16 [10] Panigrahia S K,Pradhan B.Through-the-width delamination damage propagation characteristics in single-lap laminated FRP composite joints[J].International Journal of Adhesion & Adhesives,2009,29(2):114-124 [11] Cho Y B,Averill R C.First-order zig-zag sublaminate plate theory and finite element model for laminated composite and sandwich panels[J].Composite Structures,2000,50(1):1-15 [12] Kwang-Soo K,Yeong-Moo Y,Gwang-Rae C,et al.Failure prediction and strength improvement of uni-directional composite single lap bonded joints[J].Composite Structures,2008,82(4):513-520 [13] Shin K C,Lee J J.Effects of thermal residual stresses on failure of co-cured lap joints with steel and carbon fiber epoxy composite adherends under static and fatigue tensile loads[J].Composites:Part A,2006,37(3):476-487 [14] Tay T E,Tan S H,Tan V B,et al.Damage progression by the element-failure method(EFM) and strain invariant failure theory(SIFT)[J].Composites Science and Technology,2005,65(6):935-944 [15] Davila C G,Camanho P P.Analysis of the effects of residual strains and effects on skin/stiffener debonding using decohesion elements .AIAA-2003-1465,2003 [16] Lim S H,Li Shuguang.Energy release rates for transverse cracking and delaminations induced by transverse cracks in laminated composites[J].Composites:Part A,2005,36(11):1467-1476 [17] Turon A,Camanho P P,Costa J,et al.An interface damage model for the simulation of delamination under variable-Mode ratio in Composite Materials .NASA/TM-2004-213277,2004 [18] Turon A,Davila C G,Camanho P P,et al.An engineering solution for using coarse meshes in the simulation of delamination with cohesive zone models .NASA/TM-2005-213547,2005 [19] Hiel C C,Sumich M,Chappell D P.A curved beam test specimen for determining the interlaminar tensile strength of a laminated composite[J].Journal of Composite Materials,1991,25(7):854-868 [20] Shenoi R A,Hawkins G L.Influence of material and geometry variations on the behaviour of bonded tee connections in FRP ships[J].Composites,1992,23(5):335-345 [21] 赵丽滨,彭雷,张建宇,等.复合材料π接头拉伸力学性能的试验和计算研究[J].复合材料学报,2009,26(2):181-186 Zhao Libin,Peng Lei,Zhang Jianyu,et al.Experimental and numerial research on mechanics performance of composite π joint under tensile loading [J].Acta Materiae Compositae Sinica,2009,26(2):181-186(in Chinese) [22] Hashin Z.Failure criteria for unidirectional fiber composites[J].Journal of Applied Mechanics,1980,47(2):329-334 [23] Reddy H N.Mechanics of laminated composite plates:Theory and analysis[M].Boca Raton,FL:CRC Press,1997:752-754