涡轮叶片导管快速建模

李吉星; 席平

doi:10.13700/j.bh.1001-5965.2015.0386

涡轮叶片导管快速建模

doi: 10.13700/j.bh.1001-5965.2015.0386

李吉星,
席平^,

北京航空航天大学机械工程及自动化学院, 北京100083

详细信息

作者简介:
李吉星男,博士研究生。主要研究方向:计算机辅助设计与制造、几何形状分析等。Tel.:010-82316747 E-mail:li_jixing@buaa.edu.cn;席平女,博士,教授,博士生导师。主要研究方向:飞行器辅助设计与制造、复杂曲线曲面造型等。Tel.:010-82316768 E-mail:xiping@buaa.edu.cn

通讯作者:
席平,Tel.:010-82316768 E-mail:xiping@buaa.edu.cn

中图分类号: TP391.7;V232.4
计量
- 文章访问数: 1220
- HTML全文浏览量: 210
- PDF下载量: 528
- 被引次数: 0
出版历程
- 收稿日期: 2015-06-11
- 网络出版日期: 2016-06-20

Rapid modeling of impingement pipe in turbine blade

LI Jixing,
XI Ping^,

School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 导管是涡轮叶片冲击冷却的核心部件。为实现复杂冷却结构叶片导管的快速建模,提出了创成式导管快速建模方法。首先应用截形法构建适应叶片内腔几何形状的管身截面线以创建管身,然后应用截交包络裁剪法与特征等弧长阵列方法保证了导管冲击孔与导管突起的建模稳定性与建模效率,并构建了突起定位迭代公式,保证了导管与叶片内腔的配合精度。最后采用UG Open API工具开发了导管快速建模程序,验证了所提方法的可行性。
- 导管 /
- 参数化设计 /
- 涡轮叶片 /
- 建模 /
- UG Open API
Abstract: Impingement pipe is the core component of the impingement cooling in turbine blade. In order to realize the rapid modeling of impingement pipe in turbine blade with complex cooling structure, a generative rapid modeling method was proposed.Firstly, the body of pipe was created by section curves which suits the shape of channel in blade and generated by curves created by insect-shape method. Then by using envelope surface trimming method and along-curve array method, the modeling stability and efficiency of cooling hole and hump are guaranteed.And the fitting precision between impingement pipe and blade is guaranteed by an iterative formula about protrude position.Finally, a rapid impingement pipe modeling program was developed based on UG Open API, and the modeling result validated the feasibility of the proposed method.
- impingement pipe /
- parametric design /
- turbine blade /
- modeling /
- UG Open API

HTML全文

参考文献(14)

[1]	冯国泰,顾中华,温风波,等.燃气涡轮机气冷涡轮气动设计体系设计思想及其应用[J].工程热物理学报,2009,30(11):1841-1848. FENG G T,GU Z H,WEN F B,et al.Aerodynamic design system & ideology of air-cooled turbine and its application to gas turbines[J].Journal of Engineering Thermophysics,2009,30(11):1841-1848(in Chinese).
[2]	陈凯.燃气涡轮冷却结构设计与气热弹多场耦合的数值研究[D].哈尔滨:哈尔滨工业大学,2010:6-9. CHEN K.Numerical research of gas turbine cooling structure design with aerodynamic thermal mechanical conjugate methods[D].Harbin:Harbin Institute of Technology,2010:6-9(in Chinese).
[3]	谷振鹏,王开.冲击加气膜组合式换热效果的试验研究[J].航空发动机,2010,36(5):52-55. GU Z P,WANG K.Experiments invetisgation on heat transfer effectiveness of combined implingment and film[J].Aeroengine,2010,36(5):52-55(in Chinese).
[4]	宋玉旺,席平.基于特征造型技术的涡轮叶片参数化设计[J].北京航空航天大学学报,2004,30(4):321-324. SONG Y W,XI P.Parametric design of turbine blade based onfeature modeling[J].Journal of Beijing University of Aeronautics and Astronautics,2004,30(4):321-324(in Chinese).
[5]	朱谦,宁涛,席平.基于引导线的涡轮气冷叶片伸根建模方法[J].北京航空航天大学学报,2012,38(8):1085-1089. ZHU Q,NING T,XI P.Root extending section of turbine blade modeling method based on guide curves[J].Journal of Beijing University of Aeronautics and Astronautics,2012,38(8):1085-1089(in Chinese).
[6]	张宝源,席平,杨炯.复合弯扭涡轮叶片尾缝的快速建模[J].北京航空航天大学学报,2014,40(1):48-53. ZHANG B Y,XI P,YANG J.Rapid modeling of trailing edge slots in bowed-twisted turbine blade[J].Journal of Beijing University of Aeronautics and Astronautics,2014,40(1):48-53(in Chinese).
[7]	杨炯,席平,胡毕富,等.适应弯扭隔肋的涡轮叶片多种扰流肋造型方法[J].北京航空航天大学学报,2014,40(6):775-781. YANG J,XI P,HU B F,et al.Multi-type ribs of turbine blade modeling method fitting bowed-twist wall[J].Journal of Beijing University of Aeronautics and Astronautics,2014,40(6):775-781(in Chinese).
[8]	迟重然.气冷涡轮叶片的传热设计[D].哈尔滨:哈尔滨工业大学,2011:45-56. CHI C R.Heat transferring design for air-cooling turbine blades[D].Harbin:Harbin Institute of Technology,2011:45-56(in Chinese).
[9]	王松涛,迟重然,温风波,等.涡轮动叶冷却结构设计方法Ⅰ:参数化设计[J].工程热物理学报,2011,32(4):581-584. WANG S T,CHI C R,WEN F B,et al.Cooling structures design for turbine blade I:Parametric design[J].Journal of Engineering Thermophysics,2011,32(4):581-584(in Chinese).
[10]	曹率,莫蓉,宫中伟.航空涡轮叶片气膜孔参数化建模研究[J].航空计算技术,2011,41(3):77-81. CAO S,MO R,GONG Z W.Research on parametric modeling of aeronautic turbine blade film hole[J].Aeronautical Computing Technique,2011,41(3):77-81(in Chinese).
[11]	夏禹.涡轮叶片造型CAD系统研究[D].西安:西北工业大学,2004:19-22. XIA Y.The research of turbine blade modeling CAD system[D].Xi'an:Northwestern Polytechnical University,2004:19-22(in Chinese).
[12]	CHEN R Z,XI P.Analysis-oriented parametric modeling technology[C]//20122nd International Conference on IEEE Computer Science and Network Technology (ICCSNT).Piscataway,NJ:IEEE Press,2012:1208-1211.
[13]	LIU Y,FENG X,JIANG Z,et al.High-precision modeling of turbine blade from cross-section data[C]//2010 International Conference on IEEE Measuring Technology and Mechatronics Automation(ICMTMA).Piscataway,NJ:IEEE Press,2010,2:390-393.
[14]	KORAKIANITIS T,PANTAZOPOULOS G I.Improved turbine-blade design techniques using 4th-order parametric-spline segments[J].Computer Aided Design,1993,25(5):289-299.