Li Shusuo, Zhou Chungen, Gong Shengkai, et al. Effect of ball blasting on the service properties of NiCoCrAlY coating of the alloy IC6 vane[J]. Journal of Beijing University of Aeronautics and Astronautics, 2004, 30(10): 989-992. (in Chinese)
Citation: Wang Yanzhong, Wu Canhui, Ge Xuyang, et al. Basal worm-designing method of face-gear hob[J]. Journal of Beijing University of Aeronautics and Astronautics, 2009, 35(2): 166-169. (in Chinese)

Basal worm-designing method of face-gear hob

  • Received Date: 20 Jul 2008
  • Publish Date: 28 Feb 2009
  • Face-gear drives become the main direction of research for aeronautical drives because of their special advantages. The applied coordinate systems of face-gear were set up and the equation of face-gear tooth surface was established, then the face-gear tooth surface constrain conditions for dedendum undercutting and addendum pointing were analyzed based on the face-gear transmission theory, at the same time, the disciplines were discussed on the relationships between pressure angle and the face-gear outer & inner radius in keeping with the practically calculated examples. The calculating results are useful for designing the face-gear drive. In the end, the face-gear hobbing theory was analyzed, according to the gear geometry and applied theory, the hobbing surface equation was founded. The discrete values of three-dimensional coordinates for the hobbing surface were calculated by using the method of numerical calculation. The three-dimensional basal worm model of face-gear hob was designed by recurring to the three-dimensional software.

     

  • [1] 熊威.面齿轮齿面方程与啮合方法分析 .北京:北京航空航天大学机械工程及自动化学院,2007 Xiong Wei. The analysis of equation of face-gear tooth surface and meshing method . Beijing: School of Mechanical Engineering and Automation,Beijing University of Aeronautics and Astronautics, 2007(in Chinese) [2] 王延忠,熊巍,张俐,等. 面齿轮齿面方程及其轮齿接触分析[J]. 机床与液压,2007,35(12):7-9 Wang Yanzhong, Xiong Wei, Zhang Li, et al.Tooth surface equations and tooth contact analysis of face gear[J]. Machine Tool & Hydraulics,2007,35(12):7-9(in Chinese) [3] 贺鹏.直齿面齿轮齿面生成方法与啮合仿真 ,西安:西北工业大学机电学院,2007 He Peng. Study on the formation of spur face gear tooth profile and meshing simulation . Xi-an: Mechanical & Electrical Institute,Northwestern Polytechnical University, 2007(in Chinese) [4] Litvin F L, Alfonso Fuentes. Face gear drive with helical involute pinion: geometry, generation by a shaper and a worm, avoidance of singularities and stress analysis .NASA/CR-213443,2005 [5] Litvin F L, Alfonso Fuentes, Claudio Zanzi, et al. Face gear drive with spur involute pinion: geometry, generation by a worm, stess analysis .NASA/CR-211362,2002
  • Relative Articles

    [1]ZHANG Fan, DING Mingsong, CHEN Jianqiang, LIU Wan, JIANG Tao, LI Peng, JIANG Jun. Interactive design and implementation of HPCC-oriented industrial CFD software[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2024.0810
    [2]BAN H H,ZHOU C,YAN X D. Rapid planning method for lunar direct ascent and rendezvous trajectory in emergency cases[J]. Journal of Beijing University of Aeronautics and Astronautics,2025,51(4):1352-1366 (in Chinese). doi: 10.13700/j.bh.1001-5965.2023.0160.
    [3]XIAO Y,LI Y,LI D S,et al. Influence of curing stress relaxation on profile accuracy of composites tools[J]. Journal of Beijing University of Aeronautics and Astronautics,2025,51(3):824-832 (in Chinese). doi: 10.13700/j.bh.1001-5965.2023.0109.
    [4]LIU Y S,YANG Y X,LIU Y,et al. Gust alleviation control system of flexible aircraft considering rudder efficiency[J]. Journal of Beijing University of Aeronautics and Astronautics,2025,51(1):248-256 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0952.
    [5]CHEN Xueqi, FENG Shoukun, DENG Wangqun, SONG Ziyu, YANG Hai, LIU Wenkui, HONG Jie. Effect of compression state on stiffness and dynamic characteristics of end tooth-tie rod rotor[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2024.0687
    [6]HE T Y,DONG Y,ZHOU S M,et al. Performance analysis and optimization of buffering/walking integrated lunar probe[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(8):2547-2556 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0634.
    [7]LI W T,HE Y Q,ZHANG Y Y,et al. Complex burn-back analysis and internal ballistic performance prediction of non-uniform grain[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(8):2524-2537 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0669.
    [8]SUN Y B,WANG R,ZHANG Q,et al. A cross-modality person re-identification method for visible-infrared images[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(6):2018-2025 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0554.
    [9]XIONG F,LI Q,LI J,et al. Time-triggered traffic scheduling-oriented virtual network embedding method[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(6):1982-1990 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0511.
    [10]ZHANG Xu, ZHAO Rui, LI Yu, YANG Guang, WANG Li-yan. Component of gas-injection effects on wall heat flux and skin-friction of vehicles[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2024.0009
    [11]REN W,LI J,WANG T Y,et al. Meshing theory and performance analysis of point-contact conjugate involute worm gear pair[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(10):3183-3195 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0778.
    [12]XU H,HAN J L,CHEN Y,et al. Thickness correction by lifting surface method and its application in morphing simulation of folding wing[J]. Journal of Beijing University of Aeronautics and Astronautics,2024,50(12):3806-3814 (in Chinese). doi: 10.13700/j.bh.1001-5965.2022.0926.
    [13]ZHAO Jin-peng, CENG Wei, MA Hai-teng. Method for determining Stanton number on the blunt body in supersonic flow[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2023.0800
    [14]LIU S,LU H Y,ZHANG W W,et al. Fast algorithm for grain burnback of actually shaped grains of solid motor[J]. Journal of Beijing University of Aeronautics and Astronautics,2023,49(11):3115-3123 (in Chinese). doi: 10.13700/j.bh.1001-5965.2021.0795.
    [15]ZHU W S,LYU X J,HOU Z Q,et al. Trajectory optimization of air-to-surface missile in full airspace based on combinational optimization algorithm[J]. Journal of Beijing University of Aeronautics and Astronautics,2023,49(2):344-352 (in Chinese). doi: 10.13700/j.bh.1001-5965.2021.0252.
    [16]ZOU Qi-hong, XU An-yi, LI Peng, SUN Pei-jie, LI Qian, GE Tian-shu. Experimental study on integrated solid desiccant coated heat pump system for manned spaceflight[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2022.0972
    [17]ZHU Y,XIAO S H,CHEN Z T. A registration algorithm with datum constraints and allowance constraints[J]. Journal of Beijing University of Aeronautics and Astronautics,2023,49(3):580-587 (in Chinese). doi: 10.13700/j.bh.1001-5965.2021.0314.
    [18]TONG Xiao-yan, LU Dong-sheng, BO Hui, CHANG Long. A contact angle measurement method for torsional teeth[J]. Journal of Beijing University of Aeronautics and Astronautics. doi: 10.13700/j.bh.1001-5965.2023.0721
    [19]GUAN R,HUANG Y Z,CHEN R,et al. Calculation of cutting angle and cutting force in face gear machining[J]. Journal of Beijing University of Aeronautics and Astronautics,2023,49(8):1922-1929 (in Chinese). doi: 10.13700/j.bh.1001-5965.2021.0613.
    [20]XIA Fei, XUE Jianghong, HE Zanhang, JIN Fusong. Interfacial crack growth of delaminated composite laminates under hygrothermal environment[J]. Journal of Beijing University of Aeronautics and Astronautics, 2022, 48(12): 2460-2472. doi: 10.13700/j.bh.1001-5965.2021.0137
  • 加载中

Catalog

    通讯作者: 陈斌, bchen63@163.com
    • 1. 

      沈阳化工大学材料科学与工程学院 沈阳 110142

    1. 本站搜索
    2. 百度学术搜索
    3. 万方数据库搜索
    4. CNKI搜索

    Article Metrics

    Article views(3834) PDF downloads(1650) Cited by()
    Proportional views
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return