Comparison of experimental ground testing and computational fluid dynamics for S-shaped inlet and JT15D-4 engine
-
摘要: 为进一步研究所设计的S形进气道与涡扇发动机共同工作时对发动机性能和稳定性的影响,制作了S形进气道1∶1玻璃钢模型,安装在小型涡扇发动机JT15D-4上,观察发动机在地面台架条件下的工作状态,并进行了相关数据的测量.利用CFD(Computational Fluid Dynamics)方法进行同样条件下的进气道数值仿真计算.将计算结果与实验结果相比较,结果表明:两种方法得到的数据相吻合,一方面说明所设计的S形进气道与发动机匹配良好,能够保证发动机的正常运转;另一方面说明,CFD方法可用于进气道的设计验证.Abstract: The S-shaped inlet working with the turbofan engine was discussed by using ground test and computational fluid dynamics (CFD) codes. A full scale S-shaped inlet model had been made of glass fiber reinforced plastic. The model was installed in front of the JT15D-4 turbofan engine, with the results obtained from the full scale matching ground test at Beijing. Static pressure,total pressure recovery and total pressure contours were presented. Under the same working condition, the performance of the S-shaped inlet was developed by using CFD codes. Based on comparison of CFD code to full scale measured test data, they match well. It means that on one hand the S-shaped inlet was designed properly according to the engine and they can match work together, on the other hand the CFD codes are shown to predict total pressure contours at the duct exit accurately, the CFD codes could be used for the inlet design.
-
Key words:
- S-shaped inlet /
- turbofan engine /
- ground test /
- computational fluid dynamics(CFD)
-
[1] Tormalm M.Design and analysis of compact UAV ducts[R].AIAA 2006-2828,2006 [2] Kirk A M,Gargoloff J I,Rediniotis OK,et.al.Numerical and experimental investigation of a serpentine inlet duct[R].AIAA 2007-842,2007 [3] Beale D K,Zelenakt M.Development and validation of a freejet technique for inlet-engine compatibility testing[R].AIAA-92-3921,1992 [4] Lee K,Lee B,Kang S,et al.Inlet distortion test with gas turbine engine in the altitude engine test facility[R].AIAA-2010-4337,2010 [5] 王如根,江勇,飞机进气道/发动机匹配工作流场测试和分析[J],航空计测技术,1998,18(5):11-13 Wang Rugen,Jiang Yong.Test and analysis of the flow field on air inlet/engine matching operation[J].Aviation for Test Technology,1998,18(5):11-13(in chinese) [6] 张发启,江勇,桑增产,等,某型飞机进气道对发动机性能和台架点的影响[J].推进技术,2001,22(2):137-139 Zhang Faqi,Jiang Yong,Sang Zengchan,et al.Effect of inlet on the engine performance and platform point for aircraft[J].Journal of Propulsion Technology,2001,22(2):137-139(in Chinese) [7] 江勇,陶增元,张发启,等.某型飞机进气道与发动机地面匹配实验研究[J].航空动力学报,2003,18(4):554-557 Jiang Yong,Tao Zengyuan,Zhang Faqi,et al.Matching test of an aircraft inlet and engine on the ground[J].Journal of Aerospace Power,2003,18(4):554-557(in Chinese) [8] Sutlif D L,Konno K E,HeiDelberg L J.Duct mode measurements on the TFE731-60 full scale engine[R].AIAA-2002-2564 [9] Weir D,Bouldin B,Mendoza J.Static and flight aeroacoustic evaluations of a scarf inlet[R].AIAA-2006-2462,2006 [10] Danielle K L,Validation of the predicted circumferential and radial mode sound power levels in the inlet and exhaust ducts of a fan ingesting distorted inflow[R].AIAA-2011-2808,2011 [11] 李大伟,张云飞,马东立.背负式S形进气道设计及数值分析[J].推进技术,2006,27(1):61-65 Li Dawei,Zhang Yunfei,Ma Dongli.Design and numerical investigation of dorsal S-shaped inlet[J].Journal of Propulsion Technology,2006,27(1):61-65 (in Chinese)
点击查看大图
计量
- 文章访问数: 2757
- HTML全文浏览量: 230
- PDF下载量: 508
- 被引次数: 0