复合材料开孔层板压缩渐进损伤分析

周睿; 关志东; 李星; 卓越

doi:10.13700/j.bh.1001-5965.2014.0395

复合材料开孔层板压缩渐进损伤分析

doi: 10.13700/j.bh.1001-5965.2014.0395

周睿¹,
关志东^1, ,,
李星^1,2,
卓越¹

1.
北京航空航天大学航空科学与工程学院, 北京 100191
2. 中国商用飞机有限责任公司北京民用飞机技术研究中心强度分析技术研究部, 北京 102211

基金项目: 国家重点基础研究发展计划(2010CB631103)

详细信息

作者简介:
周睿(1989—),男,黑龙江哈尔滨人,硕士研究生,jianghuaiyidao@126.com

通讯作者:
关志东(1964—),男,辽宁沈阳人,教授,zdguan@buaa.edu.cn,主要研究方向为飞行器复合材料结构设计、复合材料力学.

中图分类号: V257;TB330.1
计量
- 文章访问数: 1127
- HTML全文浏览量: 73
- PDF下载量: 680
- 被引次数: 0
出版历程
- 收稿日期: 2014-07-02
- 网络出版日期: 2015-06-20

Progressive damage analysis of open-hole composite laminates under compression load

ZHOU Rui¹,
GUAN Zhidong^{1
, ,},
LI Xing^1,2,
ZHUO Yue¹

1.
School of Aeronautic Science and Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
2. Department of Strength Analysis, Beijing Aeronautical Science & Technology Research Institute, Commercial Aircraft Corporation of China Ltd, Beijing 102211, China

摘要

摘要: 首先,针对纤维增强复合材料开孔层板进行了压缩试验,通过微距数显设备、电镜扫描和X光扫描设备检测了加载过程中的渐进损伤和试验件最终破坏模式,观测了损伤起始和45°与90°铺层间的分层现象. 其次,将复合材料开孔层板失效分为层内失效和层间失效,基于细观损伤力学MMF3理论和界面胶层单元方法建立了开孔压缩损伤跨尺度分析模型.最后,应用该模型对开孔压缩损伤起始、损伤扩展和层板破坏模式进行了预测,获得了纤维和基体损伤起始位置、分层产生位置及扩展过程、最终的分层和压入破坏等计算结果.计算结果与试验结果获得了较好的吻合,表明该计算模型适用于分析复合材料开孔压缩渐进损伤问题.
- 复合材料 /
- 开孔层板 /
- 压缩试验 /
- 渐进损伤 /
- 跨尺度
Abstract: Firstly, compressional experiments were conducted on open-hole composite laminates. The progressive damage during the loading process and the final damage mode of the specimen were detected with a digital microscope, scanning electron miroscope and an X-scan equipment. Damage initiation and delamination between layups of 45° and 90° were observed during the experiments. Secondly, the failure modes of composite laminates are divided into intra-laminar failure and inter-laminar failure. A multiscale model based on the micro-mechanics of failure MMF3 theory and the interface cohesive element method for the damage analysis of open-hole compression laminates was developed. At last, the initiation and propagation of the damage and the failure modes of the laminates were predicted with the model. Numerical results such as the damage initiation position of fiber and matrix, the delamination propagation process and the final failure modes are in good agreement with experimental results, which indicates that the model is applicable to analysis of progressive damage of open-hole composite laminates under compression load.
- composite /
- open-hole laminates /
- compressional experiment /
- progressive damage /
- multiscale

HTML全文

参考文献(15)

[1]	杜善义, 关志东.我国大型客机先进复合材料技术应对策略思考[J].复合材料学报, 2008, 25(1):1-10. Du S Y, Guan Z D.Strategic considerations for development of advanced composite technology for large commercial aircraft in China[J].Acta Materiae Compositae Sinica, 2008, 25(1):1-10(in Chinese).
[2]	Suemasu H, Takahashi H, Ishikawa T.On failure mechanisms of composite laminates with an open hole subjected to compressive load[J].Composites Science and Technology, 2006, 66(5):634-641.
[3]	Berbinau P, Scoutis C, Guz I A.Compressive failure of 0°unidirectional carbon-fibre-reinforced plastic(CFRP)laminates by fibre microbuckling[J].Composites Science and Technology, 1999, 59(9):1451-1455.
[4]	Soutis C.Damage tolerance of open-hole CFRP laminates loaded in compression[J].Composite Engineering, 1994, 4(3):317-327.
[5]	Soutis C, Curtisb P T.A method for predicting the fracture toughness of CFRP laminates failing by fiber microbuckling[J].Composites Part A:Applied Science and Manufacturing, 2000, 31(7):733-740.
[6]	Lee J, Soutis C.Thickness effect on the compressive strength of T800/924C carbon fibre-epoxy laminates[J].Composites, 2006, 36(2):213-227.
[7]	关志东, 黎增山, 刘德博, 等.复合材料层板开孔压缩损伤分析[J].复合材料学报, 2012, 29(3):167-172. Guan Z D, Li Z S, Liu D B, et al.Damage analysis of open-hole compression laminates[J].Acta Materiae Compositae Sinica, 2012, 29(3):167-172(in Chinese).
[8]	Lee H K, Kim B R.Numerical characterization of compressive response and damage evolution in laminated plates containing a cutout[J].Composites Science and Technology, 2007, 67(11):2221-2230.
[9]	American Society for Testing and Materials International.ASTM D6484/D6484M-09 Standard test method for open-hole compressive strength of polymer matrix composite laminates[S].West Conshohocken:ASTM International, 2009.
[10]	Wisnom M R, Hallett S R.The role of delamination in strength, failure mechanism and hole size effect in open hole tensile tests on quasi-isotropic laminates[J].Composites Part A:Applied Science and Manufacturing, 2009, 40(4):335-342.
[11]	Tsai S W.Strength & life of composites[M].Stanford:Stanford University, 2008:6-29-6-51.
[12]	Sun X S, Tan V B C, Tay T E.Micromechanics-based progressive failure analysis of fibre-reinforced composites with non-iterative element-failure method[J].Computers & Structures, 2011, 89(11):1103-1116.
[13]	Anon.ABAQUS user's manual[CP/CD].Version 6.10.Pawtucket:Hibbitt Karlsson and Sorensen, 2010.
[14]	Benzeggagh M L, Kenane M.Measurement of mixed-mode delamination fracture toughness of unidirectional glass/epoxy composites with mixed-mode bending apparatus[J].Composites Science and Technology, 1996, 56(4):439-449.
[15]	Turon A, Davila C G, Camanho P P, et al.An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models[J].Engineering Fracture Mechanics, 2007, 74(10):1665-1682.