考虑喷油润滑的附件机匣温度场分析

陈云霞; 刘王佳

doi:10.13700/j.bh.1001-5965.2014.0533

考虑喷油润滑的附件机匣温度场分析

doi: 10.13700/j.bh.1001-5965.2014.0533

陈云霞^,,
刘王佳

北京航空航天大学可靠性与系统工程学院, 北京 100191

详细信息

通讯作者:
陈云霞(1977—),女,安徽安庆人,教授,chenyunxia@buaa.edu.cn,主要研究方向为系统故障学、复杂系统可靠性建模与仿真等.

中图分类号: V233.1
计量
- 文章访问数: 945
- HTML全文浏览量: 84
- PDF下载量: 548
- 被引次数: 0
出版历程
- 收稿日期: 2014-08-28
- 修回日期: 2014-10-28
- 网络出版日期: 2015-07-20

Accessory gearbox temperature field analysis considering fuel injection lubrication

CHEN Yunxia^,,
LIU Wangjia

School of Reliability and System Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 附件机匣作为航空发动机重要部件之一,其产热和散热的问题比较复杂.针对以往附件机匣相关研究只关注固体域的产热、散热分析,而对滑油散热作用不能充分考虑这一问题的现状,提出了基于流体仿真思想的稳态温度场分析方法.首先,通过分析附件机匣产热、散热问题的基本规律和特点,进一步采用k-ε湍流模型来模拟机匣内的情况,多相流模型模拟滑油,并且使用多参考坐标系模拟滑油在运动过程中的换热.最后,以某附件机匣作为具体应用案例,验证了方法的正确性和可行性,从而形成了一套行之有效的使用FLUENT软件对附件机匣进行稳态温度场仿真分析的模型和方法.研究的成果对于后续附件机匣的可靠性与寿命分析有重要支撑作用.
- 附件机匣 /
- 温度场 /
- FLUENT软件 /
- 多相流 /
- 喷油润滑
Abstract: Accessory gearbox is a major component of aero-engine, and the heat production and heat dissipation problems of accessory gearbox are complex. Previous studies have focused only on solid domains thermal analysis, however oil cooling effect has not been taken full account of. Aiming to complement this, a fluid simulation based on the steady-state temperature field thinking method of analysis was proposed. Firstly, basic rules and characteristics of the heat production and heat dissipation problems of the accessory gearbox were analyzed. Then we applied the k-ε turbulence model to simulation, applied the multiphase flow model to simulate the oil, and used multiple reference coordinate system to simulate heat transfer with gear rotation. Finally, the application of a specific case of accessory gearbox verified the correctness and feasibility of the method, which formed a set of effective models and methods using FLUENT software to simulate accessory gearbox's steady state temperature field. The result plays an important supporting role for subsequent research on accessory gearbox reliability and lifetime analysis.
- accessory gearbox /
- temperature field /
- FLUENT software /
- multiphase flow /
- injection lubrication

HTML全文

参考文献(14)

[1]	林基恕.航空燃气涡轮发动机机械系统设计[M].北京: 航空工业出版社, 2005: 198-199. Lin J S.Aero gas turbine engine mechanical system design[M].Beijing: Aviation Industry Press, 2005: 198-199(in Chinese).
[2]	吕亚国, 刘振侠, 路彬, 等.航空发动机附件机匣热分析研究[J].润滑与密封, 2011, 36(10): 62-66. Lv Y G Liu Z X, Lu B, et al.Thermal analysis of aeroengine accessory gearbox[J].Lubrication Engineering, 2011, 36(10): 62-66(in Chinese).
[3]	刘志全, 沈允文, 陈国定, 等.某直升机齿轮传动系统的稳态热分析[J].中国机械工程, 1999, 10(6): 15-18. Liu Z Q, Shen Y W, Chen G D, et al.Steady-state thermal analysis of a helicopter gear transmission[J].China Mechanical Engineering, 1999, 10(6): 15-18(in Chinese).
[4]	刘志全, 沈允文, 陈国定, 等.某直升机齿轮传动系统的瞬态热分析[J].航空动力学报, 1999, 14(3): 86-89. Liu Z Q, Shen Y W, Chen G D, et al.Transient thermal analysis of a helicopter gear transmission system[J].Journal of Aerospace Power, 1999, 14(3): 86-89(in Chinese).
[5]	史妍妍, 孙志礼, 李国权, 等.附件机匣稳态热分析方法研究[J].机械设计, 2009, 26(6): 22-25.Shi Y Y, Sun Z L, Li G Q, et al.Accessory gearbox steady-state thermal analysis study[J].Journal of Machine Design, 2009, 26(6): 22-25(in Chinese).
[6]	闫明.基于ANSYS的飞机附件机匣热分析[D].沈阳: 东北大学, 2005. Yan M.Thermal analysis to the accessory gearbox based on ANSYS[D]. Shenyang: Northeastern University, 2005(in Chinese).
[7]	Berker R. Integration des equations du mouvement d'un fluide visqueux incompressible[M].Handbuch der Physik.Berlin: Springer, 1963.
[8]	Wang C Y. Exact solution of the unsteady Navier-Stokes equations[J].Annual Review of Fluid Mechanics, 1991, 23: 159-177.
[9]	宋学官, 蔡林, 张华.ANSYS流固耦合分析与工程应用实例[M].北京: 中国水利水电出版社, 2012: 3-4. Song X G, Cai L, Zhang H.ANSYS fluid-structure interaction analysis and engineering application examples[M].Beijing: China Water & Power Press, 2012: 3-4(in Chinese).
[10]	杜明刚, 张立群.综合传动装置空载功率损失研究[J].车辆与动力技术, 2004(1): 27-29.Du M G, Zhang L Q.Research on vehicle transmission power loss[J].Acta Armamentarll the Volume of Tank, Armored Vehicle and Engine, 2004(1): 27-29(in Chinese).
[11]	吴昌林.关于齿面传热系数计算法的研究[J].机械传动, 1992, 16(2): 4-8. Wu C L.Research on tooth surface heat transfer coefficient calculation method[J].Journal of Mechanical Transmission, 1992, 16(2): 4-8(in Chinese).
[12]	钟毅芳, 吴昌林, 唐增宝.机械设计[M].武汉: 华中科技大学出版社, 2001: 67-68. Zhong Y F, Wu C L, Tang Z B.Mechanical design[M].Wuhan: Huazhong University of Science & Technology Press Co., Ltd, 2001: 67-68(in Chinese).
[13]	ANSYS Manual R15.0[EB/OL].Canonsburg.PA.US., ANSYS Co, Ltd., (2013-11)[2014-06].http: //www.ansys.com.cn.
[14]	朱红钧, 林元华, 谢龙汉.FLUENT流体分析及仿真实用教程[M].北京: 人民邮电出版社, 2010: 125-128. Zhu H J, Lin Y H, X L H.FLUENT fluid analysis and simulation of practical tutorial[M].Beijing: Post & Telecom Press, 2010: 125-128(in Chinese).