力约束管材自由胀形试验研究与材料性能测试

程鹏志; 郎利辉; 葛宇龙; 阮尚文; 王韬; 武海

doi:10.13700/j.bh.1001-5965.2014.0603

力约束管材自由胀形试验研究与材料性能测试

doi: 10.13700/j.bh.1001-5965.2014.0603

1.
北京航空航天大学机械工程及自动化学院, 北京 100191
2. 上海汇众汽车制造有限公司, 上海 200122

基金项目: 国家“973”计划资助项目( 613152); 国家自然科学基金国际(地区)合作与交流资助项目(51111120088)

详细信息

作者简介:
程鹏志(1985—),男,河北石家庄人,博士生,pengzhi80h@163.com

通讯作者:
郎利辉(1970—),男,河南新乡人,教授,lang@buaa.edu.cn,主要研究方向为先进成形技术及装备.

中图分类号: V261.2⁺8
计量
- 文章访问数: 95145
- HTML全文浏览量: 58908
- PDF下载量: 996
- 被引次数: 0
出版历程
- 收稿日期: 2014-09-28
- 修回日期: 2014-11-19
- 网络出版日期: 2015-04-20

Tube free bulging experiment with force-end and material properties testing

1.
School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
2. Shanghai Huizhong Automotive Manufacturing Co., Ltd, Shanghai 200122, China

摘要

摘要: 相较于单向拉伸试验,通过管材胀形试验(TBT,Tube Bulging Test)获得的材料性能参数能够更准确地反映材料在高压流体作用下的塑性成形性能,不同的管端边界将会严重影响管材胀形试验的测试结果.针对国际上现有试验方法和设备存在的不足,研制出了一套约束边界清晰、加载精确的管材自由胀形试验系统.在管材测试过程中,基于位移随动力主动加载的控制策略和比例伺服油缸,实现实时的轴向力、轴向位移和内压力的精确加载.端部约束的测试管材通过特殊设计的工装保证了其轴向自由滑动.实时内压力和胀形管材顶点处材料的壁厚和胀形高度信息通过超高压压力传感器、超声测厚仪和磁致伸缩位移传感器采集,进而基于Swift材料本构模型和采集到的数据拟合出材料应力应变曲线和材料性能参数.试验结果表明,管材两端侧推力与内压力对管材内腔端面的作用力和管材轴向自由对称收缩的平衡条件始终处于动态稳定中,试验设备能够准确获得实时胀形高度、顶点厚度、轴向收缩长度和内压力的信息,能够为材料性能测试和工艺设计提供可信的材料参数.
- 充液成形 /
- 胀形试验 /
- 管端边界 /
- 自由滑动 /
- 轴向力 /
- 内压力 /
- 胀形高度 /
- 材料参数
Abstract: Compared with uniaxial tension, the material property parameters obtained by tube bulging test (TBT) can accurately reflect the plastic forming properties of materials under high-pressure fluid condition. Different end-conditions will seriously affect the experiment results of TBT. According to the defects of existed experimental method and equipment internationally, a special TBT system, with accurate boundary conditions and loading units, was successfully designed and developed. The axial force, axial displacement, and the internal pressure are the key points of the system which could be accurately controlled in real-time bycontrol strategy of displacement under dynamic active loading state and proportional servo valves. The free sliding of fixed tube ends was implemented by a special designed fixture. During the experimental process, the real-time thickness and bulging height in the pole, and the real-time internal pressure were monitored by the ultrasonic thickness gauge, the magnetostrictive displacement sensor and the ultra-high pressure sensor. The stress-strain curve and material properties were derived by the Swift material constitutive model and the monitor data. The experimental data demonstrate that the two load balance conditions, which are the balance of two axial forces with internal pressure and the balance of two axial contractive displacements, are always satisfied during all the test process. The test data processing results show that the monitor data have good repeatability and can be used to get the material properties.
- tube hydroforming /
- bulging test /
- end-condition /
- free sliding /
- axial force /
- internal pressure /
- bulging height /
- material properties

HTML全文

参考文献(16)

[1]	Yuan S J, Liu G.3.04-Tube hydroforming (internal high-pressure forming)[J].Comprehensive Materials Processing,2014,3:55-80.
[2]	Ahmetoglu M, Altan T.Tube hydroforming:state-of-the-art and future trends[J].Journal of Materials Processing Technology,2000,98(1):25-33.
[3]	Lang L H, Wang Z R,Kang D C,et al.Hydroforming highlights:sheet hydroforming and tube hydroforming[J].Journal of Materials Processing Technology,2004,151(1):165-177.
[4]	Ouirane A H B, Boudeau N,Velasco R,et al.Error evaluation on experimental stress-strain curve obtained from tube bulging test[J].Thin-Walled Structures,2011,49(10):1217-1224.
[5]	Thiruvarudchelvan S, Seet G L,Ang H E.Computer-monitored hydraulic bulging of tubes[J].Journal of Materials Processing Technology,1996,57(1-2):182-188.
[6]	Yang L F, Guo C.A simple experimental tooling with internal pressure source used for evaluation of material formability in tube hydroforming[J].Journal of Materials Processing Technology,2006,180(1-3):310-317.
[7]	He Z B, Yuan S J,Lin Y L.Analytical model for tube hydro-bulging test,part I:models for stress components and bulging zone profile[J].International Journal of Mechanical Sciences,2014,87:297-306.
[8]	He Z B, Yuan S J,Lin Y L.Analytical model for tube hydro-bulging test,part II:linear model for pole thickness and its application[J].International Journal of Mechanical Sciences,2014,87:307-315.
[9]	Velasco R, Boudeau N.Tube bulging test:theoretical analysis and numerical validation[J].Journal of Materials Processing Technology,2008,205(1-3):51-59.
[10]	Zribi T, Khalfallah A,BelHadjSalah H.Experimental characterization and inverse constitutive parameters identification of tubular materials for tube hydroforming process[J].Materials and Design,2013,49:866-877.
[11]	Imaninejad M, Subhash G,Loukus A.Influence of end-conditions during tube hydroforming of aluminum extrusions[J].International Journal of Mechanical Sciences,2004,46(8):1195-1212.
[12]	Imaninejad M, Subhash G,Loukus A.Experimental and numerical investigation of free-bulge formation during hydroforming of aluminum extrusions[J].Journal of Materials Processing Technology,2004,147(2):247-254.
[13]	Boudeau N, Malecot P.A simplified analytical model for post-processing experimental results from tube bulging test:theory,experimentations,simulations[J].International Journal of Mechanical Sciences,2012,65(1):1-11.
[14]	Varma N S P, Narasimhan R.A numerical study of the effect of loading conditions on tubular hydroforming[J].Journal of Materials Processing Technology,2008,196(1-3):174-183.
[15]	Liu B S, Lang L H,Zeng Y S,et al.Forming characteristic of sheet hydroforming under the influence of through-thickness normal stress[J].Journal of Materials Processing Technology,2012,212(9):1875-1884.
[16]	Strano M, Altan T.An inverse energy approach to determine the flow stress of tubular materials for hydroforming applications[J].Journal of Materials Processing Technology,2004,146(1): 92-96.