基于制造过程信息融合的产品早期失效率评估

张传良; 戴伟; 梁培东; 赵宇

doi:10.13700/j.bh.1001-5965.2014.0604

基于制造过程信息融合的产品早期失效率评估

doi: 10.13700/j.bh.1001-5965.2014.0604

张传良¹,
戴伟^1, ,,
梁培东²,
赵宇¹

1.
北京航空航天大学可靠性与系统工程学院, 北京 100191
2. 北京无线电测量研究所, 北京 100054

详细信息

作者简介:
张传良(1990-),男,安徽淮北人,硕士研究生,zcls07@163.com

通讯作者:
戴伟(1982-),男,山西大同人,讲师,dw@buaa.edu.cn,主要研究方向为机械制造质量工程与工艺可靠性.

中图分类号: TH165⁺.4;TH161⁺.1
计量
- 文章访问数: 740
- HTML全文浏览量: 62
- PDF下载量: 485
- 被引次数: 16
出版历程
- 收稿日期: 2014-09-30
- 网络出版日期: 2015-08-20

Products early failure rate evaluation based on process information fusion

1.
School of Reliability and Engineering System, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
2. Beijing Research Institute of Radio Measurement, Beijing 100054, China

摘要

摘要: 为在快速响应制造模式下充分利用制造过程多源信息,通过评价产品的早期失效率来评估特定工艺的质量,进而选取合适的工艺,提出基于制造过程信息融合的评估方法.首先建立产品早期失效率的模型,并给出参数估计的方法;其次通过对形成产品可靠性的制造过程进行分析,确定合理的信息源;再次利用信息熵得到当前加工完成的产品与类似产品的相似程度;最后确定产品早期故障率的融合分布,对当前工艺生产产品的早期故障率进行评估;并以雷达移相单元为评估对象,验证论文所提方法的可行性.
- 早期失效率 /
- 工艺评估 /
- 信息融合 /
- 信息熵 /
- 相似程度
Abstract: To select the appropriate technology, the assessment of early failure rate of product was carried out. To make full use of multi-source information to evaluate the early failure rate of the product in quick response manufacturing mode, an assessment method based on process information fusion was put forward. Firstly, the model of early failure rate was established and the method of parameter estimation was provided. Secondly, based on the analyzing of the forming process of product reliability, the reasonable source that influenced the early failure rate of products in the manufacturing process was determined. And then, by comparing the similar degree of current processing finished products and similar products, different prior distributions were determined. Finally, the fused distribution of the failure rate was determined based on the information entropy. And the case study on reliability evaluation of radar phase-shift unit is demonstrated to prove the feasibility and effectiveness of the proposed method.
- early failure rate /
- process evaluation /
- information fusion /
- information entropy /
- similar degree

HTML全文

参考文献(15)

[1]	范秀君, 许静林,张根保,等.数控机床早期故障消除技术[J].中国机械工程,2013,24(16):2241-2247. Fan X J,Xu J L,Zhang G B,et al.Technology of eliminating early failures for NC machine tool[J].Chinese Mechanical Engineering,2013,24(16):2241-2247(in Chinese).
[2]	Keller A Z, Beng C.Further applications of fuzzy logic to reliability assessment and safty analysis[J].Microelectronics Reliability,1989,29(3):399-404.
[3]	Rao S S, Reddy C P.Reliability analysis of machine tool structures[J].Journal of Engineering for Industry,1977,99(4):882-888.
[4]	Nelson W. Accelerated life testing-step-stress models and data analyses[J].IEEE Transaction on Reliability,1980,29(2):103-108.
[5]	谷振宇,何彦, 刘军.基于运行信息融合的大型设备视情维修系统[J].计算机集成制造系统,2010,16(10):2094-2100. Gu Z Y,He Y,Liu J.Condition-based maintenance system for large equipment based on running information fusion[J].Computer Integrated Manufacturing Systems,2010,16(10):2094-2100(in Chinese).
[6]	冯静,周经伦. 基于Bayes-模糊逻辑算子的小子样可靠性信息融合方法[J].航空动力学报,2008,23(9):1633-1636. Feng J,Zhou J L.Small-sample reliability information fusion approach based on Bayes-fuzzy logistic operator[J].Journal of Aerospace Power,2008,23(9):1633-1636(in Chinese).
[7]	Savchuk V P, Martz H F.Bayes reliability estimation using multiple sources of prior information:Binomial sampling[J].IEEE Trans on Reliability,1994,43(1):138-144.
[8]	Smets P. The transferable belief model for expert judgments and reliability problems[J].Reliability Engineering and System Safety,1992,38(1-2):59-66.
[9]	Zhang Q, Hua C,Xu G.A mixture Weibull proportional hazard model for mechanical system failure prediction utilising lifetime and monitoring data[J].Mechanical Systems and Signal Processing,2014,43(1-2):103-112.
[10]	Jó wiak I J. An introduction to the studies of reliability of systems using the Weibull proportional hazards model[J].Microelectronics Reliability,1997,37(6):915-918.
[11]	Jardine A K S, Anderson P M,Mann D S.Application of the Weibull proportional hazards model to aircraft and marine engine failure data[J].Quality and Reliability Engineering International,1987,3(2):77-82.
[12]	张根保,唐贤进, 廖小波,等.数控机床故障率分布曲线定量化建模及应用[J].重庆大学学报,2013,36(6):119-123. Zhang G B,Tang X J,Liao X B,et al.Quantitative modeling and application of CNC machine failure distribution curve[J].Journal of Chongqing University,2013,36(6):119-123(in Chinese).
[13]	Tillmann S, Robert L K T.Quantifying qualitative information on risks:Development of the QQIR method[J].Journal of Construction Engineering and Management,2009,135(1):56-71.
[14]	蒋平. 机械制造的工艺可靠性评估[D].长沙:国防科学技术大学,2010. Jiang P.Research on process reliability for manufacturing[D].Changsha:National University of Defense Technology,2010(in Chinese).
[15]	Yager R R. Measures of entropy and fuzziness related to aggregation operators[J].Information Sciences,1995,82(3-4):147-166.

施引文献

期刊类型引用(8)

1.	赵志彬，杨正伟，李胤，寇光杰，陈金树，张炜. 低速冲击下碳/玻混杂复合材料红外辐射特征. 北京航空航天大学学报. 2023(01): 177-186 . 本站查看
2.	石姗姗，吕超雨，吕航宇，程功，孙直. 具有Kevlar短纤维界面增韧的碳纤维/铝蜂窝夹芯板冲击后压缩性能. 复合材料学报. 2023(02): 771-781 . 百度学术
3.	刘俭辉，潘仪晨，薛文卓，孙建仁. T300/69层合板多角度冲击下的数值模拟研究. 兰州理工大学学报. 2023(03): 43-48 . 百度学术
4.	谭理成，汪舟，王晓丽，杨莹，蒋亚琴，曾飞，段芳芳，甘进. 冲头形状对复合材料层合板低速冲击力学行为影响研究. 兵器材料科学与工程. 2023(04): 1-7 . 百度学术
5.	夏法锋，张红哲，李洋. 基于3D打印技术制备CF-PLA纤维及性能研究. 塑料工业. 2023(08): 152-157 . 百度学术
6.	许良，胡鸿铭，周松，宋万万. 两次冲击距离对CFRP层合板冲击损伤和剩余压缩强度的影响. 复合材料科学与工程. 2023(12): 12-18+37 . 百度学术
7.	张梦涛，刘峰，李雪江. 碳纤维层合板低能量冲击后静强度试验研究. 新技术新工艺. 2022(01): 62-66 . 百度学术
8.	王涛，杨勇新. 低速冲击下复合材料组合板新型耗能模式研究. 复合材料科学与工程. 2022(02): 75-81 . 百度学术