基于CFD的斜盘/滑靴副油膜特性分析

马纪明; 申亚勇; 李齐林

doi:10.13700/j.bh.1001-5965.2015.0107

基于CFD的斜盘/滑靴副油膜特性分析

doi: 10.13700/j.bh.1001-5965.2015.0107

1.
北京航空航天大学中法工程师学院, 北京 100083
2. 中航工业金城南京机电液压工程研究中心, 南京 211140

基金项目: 国家自然科学基金(51205007)

详细信息

作者简介:
马纪明男,博士,高级实验师。主要研究方向:液压元件与系统设计、机电系统仿真。Tel.:010-82339761 E-mail:jiming.ma@buaa.edu.cn

通讯作者:
马纪明,Tel.:010-82339761 E-mail:jiming.ma@buaa.edu.cn

中图分类号: TH137.51
计量
- 文章访问数: 1017
- HTML全文浏览量: 102
- PDF下载量: 600
- 被引次数: 0
出版历程
- 收稿日期: 2015-03-04
- 网络出版日期: 2016-02-20

Oil film analysis of swash plate/slipper pair based on CFD

1.
Sino-French Engineer School, Beijing University of Aeronautics and Astronautics, Beijing 100083, China
2. Jincheng Nanjing Electrical and Hydraulic Engineering Research Center of AVIC, Nanjing 211140, China

摘要

摘要: 结合三维Navier-Stokes方程和任意拉格朗日-欧拉(ALE)描述方法,首先,提出了一种基于计算流体力学(CFD)的滑靴副油膜特性分析方法,该方法能综合考虑滑靴副结构参数、柱塞泵工况参数对油膜特性的影响。然后,针对某种滑靴副结构,仿真得到了24种不同工况下的油膜厚度,分析了工况(温度、转速和出口压力)与滑靴副油膜的定量关系。本文还提出了一个与油膜特性相关的液动力参数的描述公式,并基于某固定结构尺寸的滑靴副CFD仿真结果,研究证明了对于固定结构的滑靴副结构,该参数仅与油液黏度(温度)相关,与其他工况参数无关。根据液动力参数公式,可以方便地给出滑靴副油膜厚度的解析方法。最后,将基于解析方法与基于CFD仿真方法得到的油膜厚度结果进行了对比,证明了解析方法的准确性。
- 柱塞泵 /
- 斜盘/滑靴副 /
- 油膜 /
- 计算流体力学 /
- 润滑
Abstract: The 3-D Navier-Stokes equations and arbitrary Lagrangian-Eulerian (ALE) method are firstly used to present the oil film analysis method based on computational fluid dynamics (CFD), which can describe the correlation among slipper structure parameters, running conditions and oil film thickness. Then, the oil film thicknesses of a slipper bearing under 24 different running conditions are obtained by simulation method. A function is consequently obtained based on the simulation results, which can express the relationships between running conditions (temperature, rotation speed, and outlet preesure) and oil film thickness. Furthermore, an equation of hydraulic dynamic parameter is provided and used to express the oil film thickness analytically. Based on the CFD simulation results, the parameter is proven to be only related with the oil viscosity (temperature) under fixed design structure, and unrelated with other running conditions, such as rotation, pressure, and so on. It is convenient for designer to derive the oil film thickness expression equation. Finally, we compared the oil film thicknesses obtained from analytical and CFD methods, and the results show that the presented method is feasible.
- piston pump /
- swash plate/slipper pair /
- oil film /
- computational fluid dynamics /
- lubrication

HTML全文

参考文献(32)

[1]	张斌. 轴向柱塞泵的虚拟样机及油膜压力特性研究[D].杭州:浙江大学,2009:75-97. ZHANG B.Study on virtual prototype and pressure characteristics of oil film for axial piston pump[D].Hangzhou:Zhejiang University,2009:75-97(in Chinese).
[2]	李迎兵. 轴向柱塞泵滑靴油膜特性研究[D].杭州:浙江大学,2011:23-35. LI Y B.Study on characteristics of oil film for slipper pair of axial piston pumps[D].Hangzhou:Zhejiang University,2011:23-35(in Chinese).
[3]	HOOKE C J,LI K Y.The lubrication of slippers in axial piston pumps and motors-the effect of tilting couples[J].Journal of Mechanical Engineering Science,1989,203(53):343-350.
[4]	KOC E,HOOKE C J.Considerations in the design of partially hydrostatic slipper bearings[J].Tribology International,1997,30(11):815-823.
[5]	MANRING N D,WRAY C L, DONG Z.Experimental studies on the performance of slipper bearings within axial piston pumps[J].Journal of Tribology,2004,126(3):511-518.
[6]	CANBULUT F. The experimental analyses of the effects of the geometric and working parameters on the circular hydrostatic thrust bearings[J].JSME International Journal,2005,48(4):715-722.
[7]	FISHER M J. A theoretical determination of some characteristics of a tilted hydrostatic slipper bearing[R].[S.l.]:British Hydromechanics Research Association,1962.
[8]	庄欠伟,周华,艾青林.轴向柱塞泵滑靴副润滑特性实验台的研制[J].机床与液压,2005(3):113-115. ZHUANG Q W,ZHOU H,AI Q L.Development of experiment rig for lubricate film of the slipper pad in axial piston pumps[J].Machine Tools & Hydraulics,2005(3):113-115(in Chinese).
[9]	艾青林,周华,张增猛,等.轴向柱塞泵配流副与滑靴副润滑特性试验系统的研制[J].液压与气动,2004(11):22-25. AI Q L,ZHOU H,ZHANG Z M, et al.Development of lubricating characteristics testing system of friction pair in axial piston pump[J].Chinese Hydraulics & Pneumatics,2004(11):22-25(in Chinese).
[10]	NIE L, HUANG G H,LI Y R.Tribological study on hydrostatic slipper bearing with annular orifice damper for water hydraulic axial piston motor[J].Tribology International,2006,39(11):1342-1354.
[11]	马纪明,李齐林,任春宇,等.轴向柱塞泵/滑靴副润滑磨损的影响因素分析[J].北京航空航天大学学报,2015,41(3):405-410. MA J M,LI Q L,REN C Y,et al.Influence factors analysis on wear of hydraulic axial piston pump/slipper pair[J].Journal of Beijing University of Aeronautics and Astronautics,2015,41(3):405-410(in Chinese).
[12]	MA J M,CHEN J,LI J.Wear analysis of swash plate/slipper pair of axis piston hydraulic pump[J].Tribology International,2015,90:467-472.
[13]	IBOSHI N,YAMAGUCHI A.Characteristics of a slipper bearing for swash plate type axial piston pumps and motors,theoretical analysis[J].Bulletin of the JSME,1982,25(428):1921-1930.
[14]	IBOSHI N. Characteristics of a slipper bearing for swash plate type axial piston pumps and motors,design method for a slipper with a minimum power loss in fluid lubrication[J].Bulletin of the JSME,1986,129(254):2529-2538.
[15]	BERGADA J M,KUMAR S,DAVIES D L,et al.A complete analysis of axial piston pump leakage and output flow ripples[J].Applied Mathematical Modeling,2012,36(4):1731-1751.
[16]	SCHENK A,IVANTYSYNOVA M.A transient fluid structure interaction model for lubrication between the slipper and swash plate in axial piston machines[C]//Proceedings of the 9th International Fluid Power Conference(9IFK),2014,1:398-409.
[17]	KAZAMA T,YAMAGUCHI A.Application of a mixed lubrication model for hydrostatic equipment[J].Journal of Tribology,1993,115(4):686-691.
[18]	FANG Y,SHIRAKASHI M.Mixed lubrication characteristics between the piston and cylinder in hydraulic piston pump-motor[J].Journal of Tribology,1995,117(1):80-85.
[19]	BERGADA J M,WATTON J,KUMMAR S.Pressure,flow,force,and torque between the barrel and port plate in an axial piston pump[J].Journal of Dynamic Systems Measurement and Control,2008,130(1):141-148.
[20]	王彬,周华,杨华勇.轴向柱塞泵配流副油膜试验原理及控制特性[J].机械工程学报,2009,45(11):113-118. WANG B,ZHOU H,YANG H Y.Principle of oil film test on port pair of axial piston pump and control characteristics[J].Journal of Mechanical Engineering,2009,45(11):113-118(in Chinese).
[21]	BRAIDIC-MITIDIERI P,GOSMAN A D,IOANNIDES E,et al.CFD analysis of a low friction pocketed pad bearing[J].Journal of Tribology,2005,127(4):803-812.
[22]	HOUZEAUX G,CODINA R.A finite element method for the solution of rotary pumps[J].Computers & Fluids,2007,36(4):667-679.
[23]	KUMAR S,BERGADA J M,WATTON J.Axial piston pump grooved slipper analysis by CFD simulation of three-dimensional NVS equation in cylindrical coordinates[J].Computers & Fluids,2009,38(3):648-663.
[24]	KUMAR S. CFD analysis of an axial piston pump[D].Barcelona:Universidad Politecnica de Catalunya,2010:45-86.
[25]	ALMQVIST T,ALMQVIST A,LARSSON R.A comparison between computational fluid dynamic and Reynolds approaches for simulating transient EHL line contact[J].Tribology International,2004,37(1):61-69.
[26]	GUO Z,HIRANO T,KIRK R G.Application of CFD analysis for rotating machinery,Part 1:Hydrodynamic,hydrostatic bearings and squeeze film damper[J].ASME,2003,4(1):651-659.
[27]	DUARTE F,GORMAZ R,NATESAN S.Arbitrary Lagrangian-Eulerian method for Navier-Stokes equations with moving boundaries[J].Computer Methods in Applied Mechanics and Engineering,2004,193(45-47):4819-4836.
[28]	张兆顺. 流体力学[M].北京:清华大学出版社,2006:53-55. ZHANG Z S.Fluid mechanics[M].Beijing:Tsinghua University Press,2006:53-55(in Chinese).
[29]	李玉琳. 液压元件与系统设计[M].北京:北京航空航天大学出版社,1991:13-14. LI Y L.Hydraulic components and system design[M].Beijing:Beihang University Press,1991:13-14(in Chinese).
[30]	HIRT C W,AMSDEN A A,COOK J L.An arbitrary Lagrangian-Eulerian computing method for all flow speeds[J].Journal of Computational Physics,1974,14(2):227-253.
[31]	SOULAIMANI A,SAADB Y.An arbitrary Lagrangian-Eulerian finite element method for solving three-dimensional free surface flows[J].Computer Methods in Applied Mechanics and Engineering,1998,162(1-4):79-106.
[32]	CODINA R,ZIENKIEWICZ O C.CBS versus GLS stabilization of the incompressible Navier-Stokes equations and the role of the time step as stabilization parameter[J].Communications in Numerical Methods in Engineering,2002,18(2):99-112.