6PUS并联机构的运动学整机标定

樊锐; 李茜; 王丹

doi:10.13700/j.bh.1001-5965.2015.0331

6PUS并联机构的运动学整机标定

doi: 10.13700/j.bh.1001-5965.2015.0331

北京航空航天大学机械工程及自动化学院, 北京 100083

基金项目: 国家自然科学基金(51305013)

详细信息

作者简介:
樊锐男,博士,教授。主要研究方向:数控技术、传感器技术、机电控制及自动化。E-mail:fanrui@buaa.edu.cn;王丹男,博士,讲师。主要研究方向:并联机构理论与装备。E-mail:wangpick@163.com

通讯作者:
王丹,E-mail:wangpick@163.com

中图分类号: TH113
计量
- 文章访问数: 1070
- HTML全文浏览量: 102
- PDF下载量: 688
- 被引次数: 0
出版历程
- 收稿日期: 2015-05-25
- 网络出版日期: 2016-05-20

Integral kinematic calibration of 6PUS parallel mechanism

School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 首先建立了6PUS并联机构包括虎克铰铰链点、球铰铰链点、杆长以及导轨方向向量在内的54结构参数的误差雅可比矩阵。在MATLAB中使用最小二乘法建立了其标定模型,通过仿真验证了雅可比矩阵的正确性和最小二乘法参数辨识的有效性。其次采用正交试验选取位姿,用激光跟踪仪进行整机标定实验。根据标定结果,在MATLAB中采用建立的标定模型进行参数辨识,得到54结构参数。最后进行误差补偿,观察标定补偿效果。该整机标定可使单方向最大位置误差在0.030 mm,最大姿态误差在0.0007 rad;三方向最大位置误差在0.046 mm,最大姿态误差在0.0008 rad。由标定效果可知,整机标定可明显地提高运动学精度。
- 并联机构 /
- 最小二乘法 /
- 正交试验 /
- 标定 /
- 运动学精度
Abstract: Firstly, the error Jacobi matrix of 54 parameters including the centers of U-joints and S-joints, the length of each link and the guide's position vectors was derived for the target 6PUS parallel mechanism. And the calibration model was established based on least squares method in MATLAB. The correctness of Jacobi matrix and the validity of the identification method using least squares method can be proved with MATLAB simulation. Secondly, the poses were selected based on orthogonal experiment and the integral mechanism calibration experiment was carried out by a laser tracker. The 54 parameter data were obtained through parameter identification using calibration model in MATLAB based on the calibrated results. Finally, the calibrated consequence can be obtained through error compensation. The results show that after compensation, in one direction, the maximum position error of the target mechanism is 0.030 mm and the maximum angle error is 0.0007 rad, while in three directions, the maximum position error of the target mechanism is 0.046 mm and the maximum angle error is 0.0008 rad. Therefore, we did a significant improvement in kinematic precision by integral mechanism calibration.
- parallel mechanism /
- least squares method /
- orthogonal experiment /
- calibration /
- kinematic precision

HTML全文

参考文献(19)

[1]	MERLET J P.Parallel robots[M].Berlin:Springer Netherlands,2006:1.
[2]	裴葆青,陈五一,王田苗.6UPS并联机构杆长误差标定及其对动平台运动的影响分析[J].组合机床与自动化加工技术,2005(9):45-51. PEI B Q,CHEN W Y,WANG T M.Calibration of the 6PUS parallel grinding machine by vector method[J].Modular Machine Tool & Automatic Manufacturing Technique,2005(9):45-51(in Chinese).
[3]	FAN K C,ZHAO J W,CHANG T H,et al.Error analysis of a serial-parallel type machine tool[J].The International Journal of Advanced Manufacturing Technology,2002,19(3):174-179.
[4]	RYU J,CHA J.Volumetric error analysis and architecture optimization for accuracy of HexaSlide type parallel manipulators[J].Mechanism and Machine Theary,2003,38(3):227-240.
[5]	HUANG T,CHETWYND D G,WHITEHOUSE D J,et al.A general and novel approach for parameter identification of 6-DOF parallel kinematic machines[J].Mechanism and Machine Theory,2005,40(2):219-239.
[6]	JUDD R P,KNASINSKI A B.A technique to calibrate industrial robot with experimental verification.Robotics and automation[J].IEEE Transactions on Robotics and Automation,1990,6(1):20-30.
[7]	顾云鹭.六自由度并联地震模拟振动台全误差分析及标定研究[D].上海:上海交通大学,2012:13. GU Y L.Research on the total error analysis and calibration of a parallel 6-DOF earthquake simulator[D].Shanghai:Shanghai Jiao Tong University,2012:13(in Chinese).
[8]	郭江真,王丹,樊锐,等.3PRS/UPS冗余驱动并联机器人刚度特性分布[J].北京航空航天大学学报,2014,40(4):500-506. GUO J Z,WANG D,FAN R,et al.Stiffness characteristics distribution of a 3PRS/UPS parallel manipulator with actuation redundancy[J].Journal of Beijing University Aeronautics and Astronautics,2014,40(4):500-506(in Chinese).
[9]	RAUF A,PERVEZ A,RYU J.Experimental results on kinematic calibration of parallel manipulators using a partial pose measurement device[J].IEEE Transactions on Robotics,2006,22(2):379-384.
[10]	黄田,李亚,李思维,等.一种三自由度并联机构几何误差建模、灵敏度分析及装配工艺设计[J].中国科学(E辑),2002,32(5):628-636. HUANG T,LI Y,LI S W,et al.Geometric error modeling,sensitivity analysis and assembly process design of a 3-DOF parallel mechanism[J].Science in China(Series E),2002,32(5):628-636(in Chinese).
[11]	LIN H,MENG C,CHUAN H.Error analysis of parallel manipulators based on differential operators[C]//2009 IEEE International Conference on Mechatronics and Automation.Piscataway,NJ:IEEE Press,2009:1302-1306.
[12]	宋晓飞,石万凯,刘开友.6-PSS并联机构误差标定方法[J].重庆理工大学学报(自然科学版),2012,26(6):45-49. SONG X F,SHI W K,LIU K Y.Kinematic calibration of 6-PSS parallel mechanism[J].Journal of Chongqing Institute of Technology(Natural Science),2012,26(6):45-49(in Chinese).
[13]	ABTANHI M,PENDAR H,ALASTY A,et al.Experimental kinematic calibration of parallel manipulators using a relative position error measurement system[J].Robotics and Computer-Integrated Manfacturing,2010,26(6):799-804.
[14]	周万勇.并联机构几何精度研究[D].北京:北京航空航天大学,2015:111-118. ZHOU W Y.Research on geometric accuracy of parallel mechanism[D].Beijing:Beihang University,2015:111-118(in Chinese).
[15]	HE R B,ZHAO Y J,YANG S N,et al.Kinematic-parameter identification for serial-robot calibration based on POE formula[J].IEEE Transactions on Robotics,2010,26(3):411-423.
[16]	于凌涛,孙立宁,杜志江,等.并联机器人误差检测与补偿的三平面法[J].哈尔滨工程大学学报,2006,27(5):671-675. YU L T,SUN L N,DU Z J,et al.Three planes method on measuring and compensation of parallel robot[J].Journal of Harbin Engineering University,2006,27(5):671-675(in Chinese).
[17]	刘志杰.并联机器人位姿误差分析与补偿方法研究[D].秦皇岛:燕山大学,2010:37-45. LIU Z J.Study on pose error analysis and compensation of parallel robot[D].Qinhuangdao:Yanshan University,2010:37-45(in Chinese).
[18]	孙华德,陈五一,陈鼎昌.用激光跟踪仪标定并联机床的理论探讨[J].机床与液压,2002(5):16-19. SUN H D,CHEN W Y,CHEN D C.Theoretical investigation about PKM calibration using laser tracker[J].Machine Tool & Hydraulics,2002(5):16-19(in Chinese).
[19]	刘欢.用于三轴机床的广义并联加载机构的设计与研究[D].北京:北京航空航天大学,2014:70-77. LIU H.Design and research of generalized parallel loading mechanism used for three-axis machine tool[D].Beijing:Beihang University,2014:70-77(in Chinese).