喷涂粉末对Al-Cu-Fe准晶涂层组织结构的影响

蔡斐; 周春根; 宫声凯; 徐惠彬

喷涂粉末对Al-Cu-Fe准晶涂层组织结构的影响

北京航空航天大学材料科学与工程学院, 北京 100083

详细信息

中图分类号: TB 382
计量
- 文章访问数: 3319
- HTML全文浏览量: 268
- PDF下载量: 843
- 被引次数: 0
出版历程
- 收稿日期: 2004-09-08
- 网络出版日期: 2005-08-31

Effects of spraying powder composition and particle size on microstructures of Al-Cu-Fe quasicrystalline coatings

School of Materials Science and Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 准晶材料具有低热导率、低磨擦系数、良好的耐磨性和抗氧化性、高硬度、高温塑性等优异性能,使之适于作为表面防护涂层.为了提高钛合金的抗高温氧化性能和耐磨性能, 采用低压等离子喷涂方法LPPS (Low Pressure Plasma Spraying)在钛合金表面制备了Al-Cu-Fe准晶涂层.通过改变喷涂粉末的成分和粒度大小,研究了喷涂粉末对制备态涂层相结构及微观形貌的影响. 由X-射线衍射XRD(X-Ray Diffraction)、扫描电镜SEM(Scanning Electronic Microscope)分析得出:采用原子比为Al70Cu20Fe10、粒度为-325目的粉末制备的涂层,在800℃下真空退火处理2 h后,结构均匀致密,二十面体准晶相(I相)含量高,并只含有少量的β相.
- 准晶 /
- 涂层 /
- 组织结构 /
- 喷涂粉末 /
- 热处理 /
- 钛合金
Abstract: Quasicrystals have been widely applied for surface protection coating because of their distinguished properties including low thermal conductivity and coefficient of friction, remarkable oxidation and wear resistances, and high hardness etc. To improve the high temperature oxidation and wear resistance of titanium alloy, the Al-Cu-Fe quasicrystalline coatings were produced on titanium alloy substrates using LPPS (low pressure plasma spraying) method. The effect of the spraying powders on the phase structure and microstructure of as-sprayed coatings was studied by altering the composition and the size of spraying powders. The results of XRD (X-ray diffraction), SEM(scanning electronic microscope)show that the Al-Cu-Fe quasicrystalline coating is dense and uniform, by preparing from Al70Cu20Fe10 powders with particle size of –325 mesh(<44.5μm). After annealing under vacuum condition of 800℃ for 2 hours, it is observed that the icosahedron phase is the major phase together with a few β- Al (Cu, Fe) phase.
- quasicrystals /
- coatings /
- microstructure /
- spraying powder /
- heat treatment /
- titanium alloys

HTML全文

参考文献(1)

[1] 李成功, 傅恒志, 于翘, 等. 航空航天材料[M]. 北京:国防工业出版社, 2002 Li Chenggong, Fu Hengzhi, Yu Qiao, et al. Aerospace materials[M]. Beijing:National Defence Industry Press, 2002(in Chinese) [2] Kang S S, Dubois J M, von Stebut J. Tribology properties of quasicrystalline coatings[J]. J Mater Res, 1993, 8(10):2471~2481 [3] Archambault P, Janot C. Thermal conductivity of quasicrystals and associated processes[J]. MRS Bulletin, 1997, 22(11):48 [4] Zhou C G, Xu H B, Gong S K, et al. Formation and oxidation behavior of Al-Cu-Fe quasicrystal[J]. J Mater Sci Technol , 2002, 18:251~253 [5] Sordelet D J, Widener S D, Tang Y, et al. Characterization of a commercially produced Al-CuFeCr quasicrystalline coating[J]. Material Science and Engineering, 2000, A294-A296:834~837 [6] Sordelet D J, Besser M F, Logsdon J L. Abrasive wear behavior of Al-Cu-Fe quasicrystalline composite coatings[J]. Materials Science and Engineering, 1998, A255:54~65 [7] Sordelet D J, Besser M F, Kramer M J. Thermal spray quasicrystalline coatings part 1:relationships among processing, phase structure and splat morphology . Proceedings of the 15th International Thermal Spray Conference . France, 1998. 467~472 [8] Fleury E, Lee S M, Kim W T, et al. Effects of air plasma spraying parameters on the Al-Cu-Fe quasicrystalline coating layer[J]. Journal of Non-Crystalline Solids, 2000,278:194~204 [9] Fleury E, Kim Y C, Kim J S, et al. Comparative study of the tribological behavior of thermal sprayed quasicrystalline coating layers[J]. Journal of Alloys and Compounds, 2002,342:321~325 [10] 袁伟东, 邵天敏, 瑟岛, 等. 等离子喷涂——激光重熔制备AlCuFe准晶涂层的研究[J].材料工程, 2002(11):7~13 Yuan Weidong, Shao Tianmin, Se Dao, et al. Preparation of AlCuFe QC coatings by plasma spray and laser re-melting[J]. Material Engineering, 2002(11):7~13 (in Chinese)

施引文献

资源附件(0)

访问统计