含开口复合材料柱面壳压缩性能

阎崇年; 范舟; 程小全; 郦正能

含开口复合材料柱面壳压缩性能

北京航空航天大学航空科学与工程学院, 北京 100191

详细信息

中图分类号: TB33
计量
- 文章访问数: 2341
- HTML全文浏览量: 130
- PDF下载量: 590
- 被引次数: 0
出版历程
- 收稿日期: 2011-07-13
- 网络出版日期: 2012-07-30

Compressive behaviour of composite cylindrical shell with open hole

School of Aeronautic Science and Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 实验研究了含开口补强三分之一弧长复合材料柱面壳结构的压缩行为.测试的开口补强件在开口处最终发生屈曲破坏,其最终屈曲载荷为65.922 kN.利用ABAQUS有限元软件建立相应有限元模型研究其屈曲行为,将屈曲破坏形式及载荷的计算结果与实验结果进行比较,证明所建立的模型正确有效.研究结果表明:在不补强情况下,随着开口面积增加,压缩屈曲载荷并非完全递减,而是在某一个开口面积范围内具有极大和极小值;在补强情况下,如果开口面积一定,屈曲载荷与开口高度成正比,与开口宽度成反比.因此,在设计和工艺允许的情况下,应尽量增加开口高度.
- 柱面壳 /
- 开口 /
- 压缩 /
- 屈曲分析
Abstract: The compressive behavior of one-third composite cylindrical shell with opening reinforcement was studied under a compress load. The reinforced specimen was tested and failed in buckling at 65.922 kN near the open hole. A finite element model was established in ABAQUS to investigate the buckling behavior of the composite cylindrical shell. The computational results and experimental results of buckling failure mode and buckling load were compared to verify the validity of the finite element model. The results show that as opening area increases, the buckling load of the shell without reinforcement does not decrease progressively. However, in a certain range of opening area, the structure gets maximum and minimum buckling load values. While in the case of reinforcement, with the opening area being constant, the buckling load is in direct proportion with opening height, and is in inverse proportion with opening width. To considering design and workmanship, opening height should be increased.
- composite cylindrical shell /
- open /
- compression /
- buckling analysis

HTML全文

参考文献(11)

[1]	李钟海,程小全,杨琨,等.复合材料柱面壳压缩性能分析[J].复合材料学报,2011,28(1):206-210 Li Zhonghai,Cheng Xiaoquan,Yang Kun,et al.Composite properties analysis of composite cylindrical shell [J].Acta Materiae Compositae Sinica,2011,28(1):206-210(in Chinese)
[2]	李致敏.三维编织复合材料圆柱壳轴压下的屈曲分析[J].强度与环境,2007,34(4):123-127 Li Zhimin.Buckling analysis of three dimensional braided composite cylindrical shells under axial compression [J].Structure and Environment Engineering,2007,34(4):123-127(in Chinese)
[3]	Tan Qiang,Liao Xiaoyun,Gao Zhan.Stacking sequence opti-mization of laminated composite cylinder shell for maximal buckling load [J].Chinese Journal of Mechanical Engineering,2008,21(4):156-162
[4]	张苗苗,王丹,张卫红.带孔圆柱壳轴压屈曲与孔型优化[J].科学技术与工程,2011,11(9):56-61 Zhang Miaomiao,Wang dan,Zhang Weihong.Buckling analysis and shape optimization of cylinder shells with holes under axial compression[J].Science Technology and Engineering,2008,21(4):156-162(in Chinese)
[5]	杨金花,傅衣铭.具脱层复合材料层合圆柱壳的屈曲分析[J].湖南大学学报:自然科学版,2005,32(5):34-39 Yang Jinhua,Fu Yiming.Buckling Analysis of Composite Laminated Cylindrical Shell with Delamination [J].Journal of Hunan University:Natural sciences,2005,32(5):34-39(in Chinese)
[6]	Tafreshi Azam.Efficient modeling of delamination buckling in composite cylindrical shell under axial compression [J].Composite Structures,2004,64 (3/4):511-520
[7]	李钟海,程小全,张纪奎.开口复合材料柱壳屈曲与补救有限元分析[J].应用力学学报,2011,28(2):172-176 Li Zhonghai,Cheng Xiaoquan,Zhang Jikui.Finite element analysis of buckling and salvage of a composite cylindrical shell with an open hole [J].Chinese Journal Applied Mechanics,2011,28(2):172-176(in Chinese)
[8]	Vaziri A.On the buckling of cracked composite cylindrical shells under axial compression [J].Composite Structures,2007,80(1):152-158
[9]	Christos C C,Minnetyan L.Defect/damage tolerance of pressurized fiber composite shells [J].Composite Structures,2001,51(2):159-168
[10]	Chamis C C,Minnetyan L.Defect/damage tolerance of pressurized fiber composite shell [J].Composite Structures,2001,51(2):159-168
[11]	王蔓,白瑞祥,杨继新.碳纤维增强聚合物基复合材料修补空心柱体结构的屈曲分析[J].大连工业大学学报,2010,2(4):234-239 Wang Man,Bai Ruixiang,Yang Jixin.Bucking analysis of hollow cylinder structure strengthened with CFRP laminates [J].Journal of Dalian Institute of Light Industry,2010,2(4):234-239(in Chinese)