Design and optimization of elimination tool in rubber forming of TB5 titanium
-
摘要: TB5钛合金凸弯边橡皮成形时易失稳起皱.将起皱缺陷量化作为优化目标,以凸弯边起皱为缺陷考察指标和侧压块优化的目标函数,基于有限元模拟和试验设计,对不同几何参数下的侧压块橡皮成形进行了有限元模拟,分析了几何参数对起皱指标的影响程度,应用响应面法建立侧压块几何参数和起皱评价指标间的函数关系,并用拟牛顿法进行优化.建立了优化参数和成形指标间的近似函数关系及侧压块优化设计模型.通过试验验证该优化方法的有效性和正确性.Abstract: Wrinkling will occur in the rubber forming of convex flange, even for the forming of TB5 titanium when the flange height is higher. Wrinkling was quantified as objective functions. The rubber forming process with different side blank holder parameters were simulated based on the optimum design and FEM. Influences of different side blank holder parameters on the wrinkling were analyzed. The relationship with forming index was approximately expressed as a polynomial function. Optimal parameters were obtained using proper optimization methods based on the response surface methodology and quasi-Newton method. Practicability and validity of the optimization methods proposed in this work were verified by experiments.
-
Key words:
- TB5 titanium /
- convex flange /
- rubber forming /
- side blank holder /
- optimization
-
[1] 李重河,朱明,王宁,等.钛合金在飞机上的应用[J].稀有金属,2009,33(1):84-91 Li Chonghe,Zhu Ming,Wang Ning,et al.Application of titanium alloy in airplane[J].Chinese Journal of Rare Metals,2009,33(1):84-91(in Chinese) [2] Shan Debin,Lu Yan,Li Ping,et al.Experimental study on process of cold-power spinning of Ti-15-3 alloy[J].Journal of Materials Processing Technology,2001,115(3):380-383 [3] Asnafi N.On stretch and shrink flanging of sheet aluminium by fluid forming[J].Journal of Materials Processing Technology,1999,96(1/2/3):198-214 [4] Ramezani M,Ripin Z M,Ahmad R.Computer aided modelling of friction in rubber-pad forming process[J].Journal of Materials Processing Technology,2009,10(209):4925-4934 [5] 航空制造工程手册总编委员会.飞机钣金成形工艺[M].北京:航空工业出版社,1992 Aviation Editor of Manufacturing Engineering Handbook Committee.Aircraft sheet metal process[M].Beijing:Aviation Industry Press,1992(in Chinese) [6] 王福东.大曲率凸弯边零件橡皮囊液压成形工艺研究[D].南京:南京航空航天大学,2011 Wang Fudong.Study on rubber blander hydraulic forming process for shrink flanging part with large curvature[D].Nanjing:Nanjing University of Aeronautics and Astronautics,2011(in Chinese) [7] Kim J B,Yoon J W,Yang D Y,et al.Investigation into wrinkling behavior in the elliptical cup deep drawing process by finite element analysis using bifurcation theory[J].Journal of Materials Processing Technology,2001,111(1/2/3):170-174 [8] 韩金全,万敏,袁胜,等.飞机复杂蒙皮拉形模具型面设计方法[J].北京航空航天大学学报,2008,34(11):1360-1363 Han Jinquan,Wan Min,Yuan Sheng,et al.Design method for surface of stretching tool for complex aircraft skin[J].Journal of Beijing University of Aeronautics and Astronautics,2008,34(11):1360-1363(in Chinese) [9] Sun Yongna,Wan Min,Wu Xiangdong.Inverse identification of titanium alloy TB5's material parameters based on response surface methodology and quasi-Newton method[J].Advanced Composite Materials,2012,482/483/484:2012-2016 [10] Sun Yongna,Wan Min,Wu Xiangdong.Study on friction coefficient in rubber forming process of Ti-15-3 alloy[J].Transactions of Nonferrous Metals Society of China,2012,22(12):3012-3018
点击查看大图
计量
- 文章访问数: 1319
- HTML全文浏览量: 158
- PDF下载量: 489
- 被引次数: 0