Basal worm-designing method of face-gear hob
-
摘要: 面齿轮传动由于其独特的传动优点,成为航空传动的主要研究方向.根据面齿轮传动原理,建立面齿轮加工坐标系,得到了面齿轮齿面方程,分析了面齿轮齿顶变尖和齿根根切的限制条件,同时根据实际算例讨论了面齿轮内外半径随压力角变化的规律,所获得的结论对面齿轮的设计具有参考价值.最后分析面齿轮的滚切原理,根据齿轮啮合原理,建立面齿轮滚刀型面方程,采用数值计算方法,得到滚刀型面离散三维坐标值,借助三维造型软件得到面齿轮滚刀基本蜗杆三维模型.Abstract: Face-gear drives become the main direction of research for aeronautical drives because of their special advantages. The applied coordinate systems of face-gear were set up and the equation of face-gear tooth surface was established, then the face-gear tooth surface constrain conditions for dedendum undercutting and addendum pointing were analyzed based on the face-gear transmission theory, at the same time, the disciplines were discussed on the relationships between pressure angle and the face-gear outer & inner radius in keeping with the practically calculated examples. The calculating results are useful for designing the face-gear drive. In the end, the face-gear hobbing theory was analyzed, according to the gear geometry and applied theory, the hobbing surface equation was founded. The discrete values of three-dimensional coordinates for the hobbing surface were calculated by using the method of numerical calculation. The three-dimensional basal worm model of face-gear hob was designed by recurring to the three-dimensional software.
-
Key words:
- face-gear /
- equation of tooth surface /
- dedendum undercutting /
- addendum pointing /
- hob /
- worm
-
[1] 熊威.面齿轮齿面方程与啮合方法分析 .北京:北京航空航天大学机械工程及自动化学院,2007 Xiong Wei. The analysis of equation of face-gear tooth surface and meshing method . Beijing: School of Mechanical Engineering and Automation,Beijing University of Aeronautics and Astronautics, 2007(in Chinese) [2] 王延忠,熊巍,张俐,等. 面齿轮齿面方程及其轮齿接触分析[J]. 机床与液压,2007,35(12):7-9 Wang Yanzhong, Xiong Wei, Zhang Li, et al.Tooth surface equations and tooth contact analysis of face gear[J]. Machine Tool & Hydraulics,2007,35(12):7-9(in Chinese) [3] 贺鹏.直齿面齿轮齿面生成方法与啮合仿真 ,西安:西北工业大学机电学院,2007 He Peng. Study on the formation of spur face gear tooth profile and meshing simulation . Xi-an: Mechanical & Electrical Institute,Northwestern Polytechnical University, 2007(in Chinese) [4] Litvin F L, Alfonso Fuentes. Face gear drive with helical involute pinion: geometry, generation by a shaper and a worm, avoidance of singularities and stress analysis .NASA/CR-213443,2005 [5] Litvin F L, Alfonso Fuentes, Claudio Zanzi, et al. Face gear drive with spur involute pinion: geometry, generation by a worm, stess analysis .NASA/CR-211362,2002
点击查看大图
计量
- 文章访问数: 3744
- HTML全文浏览量: 158
- PDF下载量: 1648
- 被引次数: 0