变截面毛细通道中气泡的运动特性分析

曹瑜; 张佐光; 赵卫娟

变截面毛细通道中气泡的运动特性分析

北京航空航天大学材料科学与工程学院, 北京 100083

基金项目: 国家973资助项目(2003CB615602) ; 国家863资助项目(2001AA335020)

详细信息

中图分类号: TB 332
计量
- 文章访问数: 2439
- HTML全文浏览量: 52
- PDF下载量: 1096
- 被引次数: 0
出版历程
- 收稿日期: 2005-08-18
- 网络出版日期: 2006-07-31

Mobility behavior for driving bubble traversing constricted capillary tubes

School of Materials Science and Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 为了确定复合材料成型过程中气泡的运动条件,利用变截面毛细模拟通道实验系统,研究了气泡在变截面毛细管中的运动行为,分析了气泡长度、毛细管半径及液体种类对气泡垂直穿出行为的影响,并从理论角度推导出气泡穿出的临界压力方程.研究结果表明,气泡垂直穿出变截面毛细通道所需要的临界压力差,随气泡长度和毛细管半径的增大而减小,液体种类对其也有明显影响,实验结果与理论计算值基本吻合.该研究结果将为复合材料成型中工艺参数的优化提供实验依据.
- 复合材料 /
- 孔隙 /
- 气泡 /
- 运动
Abstract: Constricted capillary tubes were used in order to study bubble mobility condition in composite material during cure processing. The effects of bubble length, radius of capillary tube and the variety of liquid on the drive critical condition of a single bubble traversing through a joint of flow channel of constricted capillary tubes were studied. The results demonstrate that the critical pressure difference of bubble traversing through joint of constricted capillary tubes perpendicularly decreases with the increase of bubble length or the radius of capillary tube, and is also affected by the variety of liquid obviously. The experimental result tallies with the theoretical results, and the study has a certain reference value to optimize cure processing to reduce and remove voids in composites.
- composite materials /
- void /
- bubble /
- mobility

HTML全文

参考文献(1)

[1] 盛磊.纤维复合材料中孔隙的起因评述[J].航天返回与遥感,1996,17(2):42-53 Sheng Lei. An overview of causes on porosity in fiber composites[J]. Spacecraft Recovery & Remote Sensing,1996,17(2):42-53(in Chinese) [2] Boey F Y C,Lye S W. Void reduction in autoclave processing of thermoset composites part 1:high pressure effects on void reduction[J]. Composties,1992,23(4):261-265 [3] 李辰砂,冷劲松,杜善义,等.纤维增强层合复合材料固化过程的研究[J].纤维复合材料,1999(1):1-6 Li Chensha,Leng Jingsong,Du Shanyi,et al.Study on curing process of fiber reinforced composite laminates[J].Fiber Composits,1999(1):1-6(in Chinese) [4] Kardos J L,Dave R,Dudukovic M P. Voids in composites[J]. Polymer Engineering and Science,1981,21(9):518-533 [5] Loos A C,Springer G S. Curing of epoxy matrix composites[J]. Journal of Composite Materials,1983(17):135-169 [6] Wood J R,Bader M G . Void control for polymer-matrix composites (1):theoretical and experimental methods for determining the growth and collapse of gas bubbles[J]. Composites Manufacturing,1994,5(3):139-147 [7] Patel N,Rohatgi V,Lee L J. Micro scale flow behavior and void formation mechanism during impregnation through a unidirectional stitched fiberglass mat[J]. Polymer Engineering and Science,1995,35(10):837-851 [8] Patel N,Lee L J. Modeling of void formation and removal in liquid composite molding part Ⅱ:model development and implementation[J].Polymer Composites,1996,17(1):104-114 [9] Lundstrm T S. Bubble transport through constricted capillary tubes with application to resin transfer molding[J]. Polymer Composites,1996,17(6):770-779 [10] 郭烈锦.两相与多相流动力学[M].西安:西安交通大学出版社,2000:378-379 Guo Liejin. Two-phase and multiphase dynamics [M]. Xi′an:Xi′an Jiaotong University Press, 2000:378-379(in Chinese) [11] 张远君.两相流体动力学[M].北京:北京航空学院出版社,1987:349-350 Zhang Yuanjun. Two-fluid hydrodynamic[M].Beijing:Beijing Aeronautics Institute Press,1987:349-350(in Chinese) [12] José B,David Q. Rise of liquids and bubbles in angular capillary tubes[J]. Journal of Colloid and Interface Science, 2002(247):162-166

施引文献

资源附件(0)

访问统计