基于结构光视觉的钢轨磨耗测量方法

孙军华; 王伟华; 刘震; 张广军

基于结构光视觉的钢轨磨耗测量方法

北京航空航天大学仪器科学与光电工程学院, 北京 100191

基金项目: 国家自然科学基金资助项目(50727502, 60804060); 铁道部科技研究开发计划资助项目(2008G020-C)

详细信息

作者简介:
孙军华(1975-),男,湖北荆门人,副教授,sjh@buaa.edu.cn.

中图分类号: TN 247
计量
- 文章访问数: 4332
- HTML全文浏览量: 236
- PDF下载量: 1488
- 被引次数: 0
出版历程
- 收稿日期: 2009-07-16
- 网络出版日期: 2010-09-30

Rail wear measurement method based on structured-light vision

School of Instrument Science and Opto-electronics Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 分析了基于结构光视觉的钢轨磨耗测量原理,提出一种钢轨磨耗车载动态测量方法.结构光视觉传感器安装在列车底部,测量钢轨内侧横断面轮廓.以钢轨轨腰轮廓作为测量基准,利用最近点迭代(ICP,Iterative Closest Point)算法确定光平面测量坐标系到设计坐标系的旋转矩阵和平移向量,将测量轮廓与设计轮廓对齐,在此基础上计算磨耗值.与已有的方法相比,该方法无需单独设置用于基准测量的视觉传感器,采用同一传感器实现了基准测量和磨耗测量,有效降低了系统成本,操作性强,且无需进行多传感器的全局校准,保证了测量精度.实验结果表明:该钢轨磨耗测量方法具有较好的重复性精度.
- 钢轨磨耗 /
- 结构光 /
- 基准对齐 /
- 最近点迭代匹配
Abstract: The principle of rail wear measurement based on structured-light vision was analyzed. A method for dynamically measuring rail wears in vehicle-mounted was proposed. The structured-light vision sensor was installed at the bottom of the train, and the section profile of the rail was measured. Taking rail waist as measurement benchmark, the rotation matrix and translation vector between light-plane coordinate frame and designed coordinate frame were estimated by iterative closest point (ICP) algorithm, then, the rail waist profile was registered to designed profile, based on which the rail wears were calculated. Compared with previous methods, the proposed method does not need a specially vision sensor to measure the benchmark. Benchmark measurement and wear measurement are achieved with one same vision sensor. System cost is effectively reduced, and it is operable. Measurement accuracy is also guaranteed due to no need of global calibration of multi-sensor. The experimental results show that the repeatability precision of the method is high.
- rail wear /
- structured-light /
- benchmark alignment /
- iterative closest point

HTML全文

参考文献(1)

[1] 丁大尉,纪淑波,王立志.光电式钢轨磨损实时检测系统[J].中国铁道科学,2006,27(1):64-67 Ding Dawei,Ji Shubo,Wang Lizhi.Photoelectric real-time detection system for rail abrasion[J].China Railway Science,2006,27(1):64-67 (in Chinese) [2] Alippi C,Casagrande E, Scotti F,et al.Composite real-time image processing for railways track profile measurement[J]. IEEE Transactions on Instrumentation and Measurement,2000,49(3):559-564 [3] 何红涛,何长江,李华文,等.应用微机图像处理技术实现钢轨磨耗自动测量的研究[J].铁道学报,1994,16(4):43-49 He Hongtao,He Changjiang, Li Huawen,et al.Application of image procession to realizing the research of the automatic measurement of rail wear[J].Journal of the China Railway Society,1994,16(4):43-49(in Chinese) [4] Jin Wenrui,Zhan Xingqun,Jiang Benhe.Non-contact rail-wear inspecting system based on image understanding //Proceedings of the 2007 IEEE,International Conference on Mechatronics and Automation.Harbin: ,2007:3854-3858 [5] Zhang Z Y,Member S.A flexible new technique for camera calibration[J].IEEE Transactions on Pattern Analysis and Machine Intelligence,2000,22(11):1330-1334 [6] Zhou Fuqiang,Zhang Guangjun.Complete calibration of a structured light stripe vision sensor through planar target of unknown orientations[J].Image and Vision Computing,2005,23(1):59-67 [7] 孙军华,张广军,刘谦哲,等.结构光视觉传感器通用现场标定方法[J].机械工程学报,2009,45(3):174-177 Sun Junhua,Zhang Guangjun,Liu Qianzhe,et al.Universal method for calibrating structured-light vision sensor on the spot[J].Journal of Mechanical Engineering,2009,45(3):174-177(in Chinese) [8] Besl P J,McKay N D.A method for registration of 3-D shapes[J].IEEE Transactions on Pattern Analysis and Machine Intelligence,1992,14(2):239-256 [9] 铁运 [2006] 146号铁路线路修理规则[S] Ministry of railways [2006] 146 Rails of Chinese railway maintenance[S](in Chinese)

施引文献

资源附件(0)

访问统计