双级低滞后刷式密封级间不均衡性分析

文龙; 王之栎; 丁蕾; 刘健; 胡广阳; 陈聪慧

doi:10.13700/j.bh.1001-5965.2013.0523

双级低滞后刷式密封级间不均衡性分析

doi: 10.13700/j.bh.1001-5965.2013.0523

1. 北京航空航天大学机械工程及自动化学院, 北京 100191;
2. 中国航空工业集团公司沈阳发动机设计研究所, 沈阳 110015

详细信息

作者简介:
文龙（1988-），男，湖北十堰人，硕士生，wenlongbuaa@126.com.

中图分类号: V233
计量
- 文章访问数: 1025
- HTML全文浏览量: 44
- PDF下载量: 399
- 被引次数: 0
出版历程
- 收稿日期: 2013-09-22
- 网络出版日期: 2014-08-20

Inter-stage imbalance analysis of two-stage low hysteresis brush seal

1. School of Mechanical Engineering and Automation, Beijing University Aeronautics and Astronautics, Beijing 100191, China;
2. Shenyang Aero Engine Research Institute, Aviation Industry Corporation of China, Shenyang 110015, China

摘要

摘要: 针对一种结构参数的双级低滞后刷式密封，采用多孔介质模型进行流场计算，对刷丝安装角度以及第二级前板间隙高度和背板间隙高度与分压比的关系进行分析；基于梁弯曲理论和刷丝区域压力分布，采用有限元法计算得到刷丝的受力和变形情况，分析参数对转子所受摩擦扭矩的影响，讨论参数对双级低滞后刷式密封级间不均衡性的影响.分析表明，第一级刷丝安装角度的增大和第二级刷丝安装角的减小能在一定程度上使两级分压趋于均衡.第一级结构参数不变时，第二级的前板间隙高度变化对级间不均衡性影响不大，背板间隙高度在特定值时，两级可达到均衡状态.
- 双级低滞后刷式密封 /
- 多孔介质 /
- 分压比 /
- 摩擦扭矩 /
- 级间不均衡性
Abstract: The flow field of a two-stage low hysteresis brush seal with certain structure was computed with porous medium model. The relationship between seal installation angles, front and back plate gap clearance height of the second stage and partial pressure ratio were also analyzed. Based on cantilever beam theory and the pressure distribution, bristle forces and deflections were calculated with the finite element method, and the effects of parameters on friction torque and inter-stage imbalance were discussed. The result indicates that, increase of the first stage bristle angle and decrease of the second stage bristle angle could make the partial pressure tend to equilibrium. With the given structure of first stage seal, different front plate gap clearance heights of the second stage seal have little effect on inter-stage imbalance, and a specific back plate gap clearance height can make the two stages get an equilibrium state.
- two-stage low hysteresis brush seal /
- porous medium /
- partial pressure ratio /
- friction torque /
- inter-stage imbalance

HTML全文

参考文献(15)

[1]	孙晓萍,李卫东,刘晓远. 刷式密封设计与试验研究[J].航空发动机,2005,31(2):17-19 Sun Xiaoping,Li Weidong,Liu Xiaoyuan.The design and experimental investigation of brush seals[J].Aeroengine,2005, 31(2): 17-19(in Chinese)
[2]	刘占生,叶建槐. 刷式密封接触动力学特性研究[J].航空动力学报,2002,17(5):635-640 Liu Zhansheng,Ye Jianhuai.Research on structural dynamic characteristics of brush seals[J].Journal of Aerospace Power,2002,17(5):635-640(in Chinese)
[3]	Guardino C, Chew J W.Numerical simulation of three-dimensional bristle bending in brush seals[J].SME Journal of Engineering for Gas Turbines and Power,2005,127:583-591
[4]	Flower R. Brush seal development system[C]//AIAA/SAE/ASME/ASEE 26th Joint Propulsion Conference.Orlando,FL:[s.n.],1990:16-18
[5]	Hendricks R C, Griffin T A,Kline T R,et al.Relative performance comparison between baseline labyrinth and dual-brush compressor discharge seal in a t-700 engine test[R].NASA Technical Memorandum 106360,1994
[6]	Aksit M F, Tichy J A.Wear of brush seals: background and new modeling approach[J].Tribol Trans,1998,41(3):368-374
[7]	Wood P E, Jones T V.A test facility for the measurement of torques at the shaft to seal interface in brush seals[J].Journal of Engineering for Gas Turbines and Power,1999,121(1):160-166
[8]	Chupp R E, Hoiie G F.Simple leakage flow model for brush seals[C]//AIAA/SAE/ASME/ASEE,27th Joint Propulsion Conference.Sacramento,CA:[s.n.],1991:24-26
[9]	胡广阳. 航空发动机密封技术应用研究[J].航空发动机,2012,38(3):1-4 Hu Guangyang.Aircraft engine sealing technology application research[J].Aeroengine,2012,38(3):1-4(in Chinese)
[10]	Tseng T W, Short J F,Steinetz B M.Development of a low hysteresis brush seal for modern engine application[R].AIAA-1999-2683,1999
[11]	Patankar S V. 传热与流体流动的数值模拟[M].张政泽译.北京:科学出版社,1984 Pantankar S V.Numerical heat transfer and fluid flow[M]. Translated by Zhang Zhengze.Beijing:Science Press,1984(in Chinese)
[12]	Chew J W, Lapworth B L,Millener P J.Mathematical modeling of brush seals[J].Int J Heat and Fluid Flow,1995,16(6): 493- 500
[13]	王之栎,梁小峰,宋飞,等. 低滞后刷式密封数值分析[J].北京航空航天大学学报,2008,34(9):1080-1083 Wang Zhili,Liang Xiaofeng,Song Fei,et al.Low hysteresis brush seal numerical simulation[J].Journal of Beijing University of Aeronautics and Astronautics,2008,34(9):1080-1083(in Chinese)
[14]	Logan D L. 有限元方法基础教程[M].伍义生译.3版.北京:电子工业出版社,2003 Logan D L.Basic tutorial of finite element method[M].Translated by Wu Yisheng.3rd ed.Beijing:Beijing Electronic Industry Press,2003(in Chinese)
[15]	王之栎,郭苗苗,李理科. 刷密封刷丝力学行为与密封性能[J].北京航空航天大学学报,2011,37(10):1219-1222 Wang Zhili,Guo Miaomiao,Li Like.Mechanical behaviors of brush seals and sealing performance[J].Journal of Beijing University of Aeronautics and Astronautics,2011,37(10):1219-1222(in Chinese)