气冷喷油杆隔热套高度对混合扩压器性能影响

刘友宏; 周开福; 牛俊杰

doi:10.13700/j.bh.1001-5965.2015.0425

气冷喷油杆隔热套高度对混合扩压器性能影响

doi: 10.13700/j.bh.1001-5965.2015.0425

北京航空航天大学能源与动力工程学院, 北京 100083

详细信息

作者简介:
刘友宏男,博士,教授,博士生导师。主要研究方向:传热传质学、传热与红外隐身、推进系统新技术、高效节能新技术、加力涡轮喷口等热端部件气动热力学及热防护等。Tel.:010-82338358 E-mail:liuyh2@qq.com;周开福男,硕士研究生。主要研究方向:传热传质学及加力涡轮喷口热端部件气动热力学及热防护。E-mail:zkf_1991@sina.com

通讯作者:
刘友宏,Tel.:010-82338358 E-mail:liuyh2@qq.com

中图分类号: V231.3;TB553
计量
- 文章访问数: 783
- HTML全文浏览量: 26
- PDF下载量: 460
- 被引次数: 0
出版历程
- 收稿日期: 2015-06-25
- 网络出版日期: 2016-06-20

Effect of air cooled spraybar heat insulation sleeve height on performance of mixer and diffuser

School of Energy and Power Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 针对一种带气冷喷油杆的混合扩压器,基于Navier-Stokes方程组建立了流场三维数值计算模型,研究了气冷喷油杆的隔热套高度对一体化混合扩压器流场、流阻特性和混合特性的气动热力性能影响规律。结果表明:隔热套高度对混合扩压器热混合效率影响不大,总体变化范围小于0.008;随着隔热套高度的增加,静压恢复系数逐渐减小,流阻系数和压力损失系数逐渐增大;在混合扩压器出口截面处,总压恢复系数随隔热套高度增加而逐渐减小,且总体变化范围较小,由0.991 1减小到0.990 7。
- 气冷喷油杆 /
- 隔热套高度 /
- 混合扩压器 /
- 流阻特性 /
- 混合特性
Abstract: For the mixer and diffuser of air cooled spraybar rod, the three-dimensional numerical simulation model based on the Navier-Stokes equation was created. Through numerical simulation, the principle of the effect of different air cooled spraybar heat insulation sleeve heights on the mixer and diffuser integration aerothermodynamic performance of flow fluid, flow resistance characteristics and mixing characteristics was obtained. The results show that air cooled spraybar heat-insulation-sleeve height has little effect on the thermal efficiency of the mixer and diffuser, and that the overall range of variation is less than 0.008. The static-pressure recovery coefficient declines as the air cooled spraybar heat-insulation-sleeve height increases; the flow resistance and pressure loss coefficients of the mixer and diffuser increase with the growing height of air cooled spraybar heat-insulation-sleeve. At the outlet section of the mixer and diffuser, the total-pressure recovery coefficient declines as the air cooled spraybar heat-insulation-sleeve height increases, and the total variation range is small andreduced from 0.991 1 to 0.990 7.
- air cooled spraybar /
- heat insulation sleeve height /
- mixer and diffuser /
- flow resistance characteristics /
- mixing characteristics

HTML全文

参考文献(16)

[1]	PRESZ W M,REYNOLDS G,MCCORMICK D C.Thrust augment using mixer-ejector-diffuser systems:AIAA-1994-0020[R].Reston:AIAA,1994.
[2]	张靖周,李立国,高潮,等.波瓣喷管红外抑制系统的实验研究[J].航空动力学报,1997,12(2):212-214. ZHANG J Z,LI L G,GAO C,et al.An experimental study on a lobed nozzle of an infrared suppression system[J].Journal of Aerospace Power,1997,12(2):212-214(in Chinese).
[3]	刘友宏,樊超,谢翌,等.波瓣数对波瓣强迫混合排气系统性能影响[J].航空动力学报,2010,25(8):1683-1689. LIU Y H,FAN C,XIE Y,et al.Effect of lobe numbers on the performance of a lobed mixer in the forced mixing exhaust system[J].Journal of Aerospace Power,2010,25(8):1683-1689(in Chinese).
[4]	谢翌,刘友宏.瓣高宽比对波瓣强迫混合排气系统性能影响[J].航空动力学报,2010,25(12):2787-2794. XIE Y,LIU Y H.Effect of ratio of height to width of lobe on the performance of a lobed mixer in a forced mixing exhaust system[J].Journal of Aerospace Power,2010,25(12):2787-2794(in Chinese).
[5]	WAITZ I A,QIU Y J,MANNING T A,et al.Enhanced mixing with stream wise vorticity[J].Progress in Aerospace Sciences,1997,33(5-6):323-351.
[6]	OOBA Y,KODAMA H,NAKAMURA Y,et al.Large eddy simulation analysis of an 18-lobe convoluted mixed nozzle:AIAA-2002-0717[R].Reston:AIAA,2002.
[7]	MCCORMICK D C,JR BENNETT J C.Vertical and turbulent structure of a lobed mixer free shear layer:AIAA-1993-0219[R].Reston:AIAA,1993.
[8]	谢翌,阮登芳,钟晨,等.波瓣帽罩结构和脊线对混合排气系统性能影响[J].推进技术,2014,35(3):314-319. XIE Y,RUAN D F,ZHONG C,et al.Effects of lobe cap and crest line on performance of mixing exhaust system[J].Journal of Propulsion Technology,2014,35(3):314-319(in Chinese).
[9]	MENGLE V G,DALTON W N.Lobed mixer design for noise suppression:Acoustic and aerodynamic test data analysis:NASA/CR-2002-210823[R].Washington,D.C.:NASA,2002.
[10]	张哲衡,王东明,张宝华,等.波瓣混合器流场试验[J].航空动力学报,2014,29(8):1761-1768. ZHANG Z H,WANG D M,ZHANG B H,et al.Experiment of flow in lobed mixer[J].Journal of Aerospace Power,2014,29(8):1761-1768(in Chinese).
[11]	COOPER N J,MERATI P,HU H.Numerical simulation of the vertical structures in a lobed jet mixing flow:AIAA-2005-0635[R].Reston:AIAA,2005.
[12]	谢翌,李腾,刘友宏.波瓣混合器混合流场中涡结构的数值研究[J].科学技术与工程,2011,11(32):7972-7978. XIE Y,LI T,LIU Y H.Numerical investigation of vertical structures in a jet mixing flow of lobed mixer[J].Science Technology and Engineering,2011,11(32):7972-7978(in Chinese).
[13]	刘友宏,谢翌.菊花形混合器混合效率理论计算[J].航空动力学报,2009,24(4):740-745. LIU Y H,XIE Y.Analytical solution of mixing efficiency of lobed mixer[J].Journal of Aerospace Power,2009,24(4):740-745(in Chinese).
[14]	XIE Y,LIU Y H.A modified thermal mixing efficiency and its application to lobed mixer nozzle for aero-engines[J].Heat Transfer Research,2011,42(4):317-335.
[15]	郭楠.菊花形混合器流场计算与设计优化[D].北京:北京航空航天大学,2008:35-37. GUO N.Numerical simulation of the flow field and the optimal design of lobed mixer[D].Beijing:Beihang University,2008:35-37(in Chinese).
[16]	刘友宏,陈中原.非对称波瓣上外扩张角对S弯二元喷管性能影响[J].推进技术,2015,36(11):1616-1623. LIU Y H,CHEN Z Y.Effects of upward-outward penetration angle of asymmetric lobed mixer on aerothermodynamics performance of an S-shaped two-dimensional nozzle[J].Journal of Propulsion Technology,2015,36(11):1616-1623(in Chines).